#MT-200S PCB Cleaner Catalog | Explore Tumblr Posts and Blogs

mactechsmt-blog · 6 years

Text

MT-200S PCB Cleaner Catalog

Equipment Characteristics

1. Control panel interface operation, function switch, easy to operate.

2. PLC control system, multiple electrical circuit protection design, safe and stable.

3. Track transmission speed, clean brush speed settings can be adjusted.

4. Can be applied to AI after SMT process. PCB cleaning, roller, brush cleaning can work independent. Flexible and large.

5. Patented coupling drive structure, more benefit to machine operation, longer component life.

6. Standard SMEMA Communication mode, configure the Quick Connector and connect to any device.

7. Corner position must be used to prevent collision, scratches and other safety risks.

8. Unit entrances and exits have SENSOR anti-stop devices; presence of personnel hand or other parts of the body detected, equipment will emit sound and light alarm.

9. Unit entrance is required to install with protective cover. During operation, keep machine protective cover to avoid accidents and other hazards.

Machine FeaturesHigh voltage Generator + Ion Rod + Ion wind knife

Wind-knife electrostatic elimination, sometimes called ionic gas knife or ion wind knife. Mainly composed of ion rods and wind knives. Ion rods in high pressure produced a large number of positive and negative ions, but because the ions cannot reach long distance and often difficult to exceed 3 cm reach, ion bar is supported by a wind knife. Through the wind knife blower air curtain as a carrier, a large number of ions is blown to the surface to eliminate electrostatic objects, and the surface of the product electrostatic, while the airflow can also blow off surface dust and other particles. Can be used for printing code, painting, medicine container, TFT material such as large fan need to eliminate static electricity.

Vacuum Dust Collector

After ESD Brush clean the PCB, vacuum will absorb dust upward and will go into this vacuum dust collector. Dust has four filters inside.

Important Security Matters

1. Do not extend head and hand inside the machine when the device is running.

2. When the dust shield (if any) is lifted, do not extend head and hand inside the machine.

3. Accessories: Work table, Please do not reply on and press.

4. Non-placement of clutter in a device

5. Device cannot be placed in dripping or rain-soaked places.

6. To operate the device, follow the instructions.

7. Do not place the power cord and link line on the walkway.

8. Please provide the voltage and pressure to meet the requirements of the equipment, so as not to cause equipment failure

9. Do not open the distribution box at will, if needed, please arrange professional electrician to work for it.

Note

The company's equipment has been strictly tested in the factory, performance assurance and good quality control in order to ensure the interests of customers. Machine Warranty will not be applicable for problems caused by following situation. (but our company will offer spare parts with zero profit). 1. The machine device has expired the warranty period.

2. Due to a natural disaster, lightning, such as an irresistible force or inadvertent damage caused by man-made.

3. due to improper use, improper storage (maintenance) or external environmental factors, the failure or damage caused by the cause of the manufacture of the product. a. Power supply specifications are inconsistent, misuse, negligence or other improper use (maintenance) and other things. b. rodent, cockroach, ant harm and other pests. c. Sulphur area, seaside, chemical plant, biogas and other external environmental factors. d. Connection to its equipment and other external forces over voltage damage.

4. Self (or entrust others) disassembly, arbitrary change of specifications or not the company's original accessories caused by failure and damage.

5. After installation, the device location migration or removal caused failure or damage.

6. Consumables: belts ... and so on

7. Exceeded standard technical requirements to use aging or failure.

#MT-200S PCB Cleaner Catalog #Mactech

0 notes

mactechsmt-blog · 6 years

Text

MT-200 PCB Cleaner Catalog

MT-200 PCB Cleaner Catalog

Performance Characteristics

1.Our newly developed automatic compound PCB cleaner mainly designed for (SMT) surface mount manufacturing process, suitable for PCB board after laser marking; solder paste printing or viscose coating before the fine line surface cleaning. Remove particles and other foreign matter, to ensure that the PCB surface is in a clean condition. In addition to the static electricity system effectively eliminates static electricity remaining on the board and effectively controls defects and damages that may occur due to dust and static electricity in advance, thereby reducing hidden dangers and improving product quality. Allow you to have the most advanced contact cleaning system.

2.Fully automatic PCB cleaning machine brush cleaning, vacuum cleaning system, static elimination system and roller dust removal system. Electrostatic rollers and sticky paper combinations are recognized as the most efficient cleaning systems in the market today.

3.Electrostatic elimination system (patented technology) The main elimination of residual PCB printing and patch components brought unpredictable consequences, due to electrostatic discharge on the main electrostatic sensitive components, Such as: IGBT, FET, blue and white backlight, LCD, chips and so on

There are two kinds of damage and damage caused by sudden damage and potential damage. The so-called sudden injury, refers to the device was severely damaged, loss of function. This damage can usually be detected during the quality inspection in the production process, so the cost to the factory is mainly rework. Potential damage is the damaged part of the device, the function has not been lost, and cannot be found during the testing of the production process, but in use will make the product become unstable, good or bad, so the quality of the product constitutes greater damage.

Configuration Characteristics

The newly developed brush and vacuum combination of the main laser marking of larger particles of dust cleaning, so as not to scratch the electrostatic roller.

Contact cleaning, electrostatic wheel can clean 1 micron size dust particles, high efficiency and high energy while also ensuring the PCB cleanliness.

Nien dust paper sheet design, the electrostatic wheel can effectively transfer the dust particles and stored in the reverse sticky paper, so that it can achieve uninterrupted dust removal work. When the outer sticky paper saturated, peel this Sticky paper, brand new next sticky paper is used, convenient and quick.

Unique design, adjustable support system to ensure that different sizes, different thickness PCB 100% contact with the clear electrostatic roller, making it to ensure the best cleaning results.

Import and export are equipped with static eliminator, the main elimination of residual static discharge due to electrostatic discharge on the main electrostatic sensitive components and unpredictable consequences.

Unique patented design and adjustable plate thickness adjustment device to meet all current SMT processes, such as 0.4 ~ 3.0mm bare board and 3.0 ~ 7.0mm fixture can easily adjust through.

Separated alarm lights and alarm bell system allows any operator to keep abreast of the working status of the machine.

Specialty Characteristics

1. Operating system completely independent development (patented technology), simple operation, with complete independent intellectual property rights. Guide for the customer upgrade and other services.

2. Electrostatic roller (patented technology), the first complete master of drum hardness, viscosity, electrostatic coefficient, coefficient of friction, gel density and other full set of technology manufacturers.

3. Unique patented design, to ensure that different processes of different thickness of the PCB board can pass.

Option:

Static electricity real-time monitoring system: The engineer can set the limit of static electricity according to the need. When the static electricity value exceeds the limit, the monitoring system will alarm and make the machine stop working automatically. These parameters can be changed and stored and displayed through the display.

Technical Parameter

1. Dimensions: Dimensions (L × W × H): 550x650x1520mm

2. PCB size: (L × W) ~ (L × W) 50 * 50 ~ 350 * 250 (MM) (Other sizes are available upon request)

3. PCB thickness: 0.6-3.0mm or (customer specified: optional 06. ~ 7.0mm)

4. transmission direction: track fixed left to right (right to left optional)

5. Transmission height: 910 ± 20 (MM)

6. Power supply: AC220V / 50-60HZ

7. Transmission motor: Zhongda speed motor.

8. Control system: the use of Panasonic PLC control, Japan Panasonic SENSOR control start

9. Control Panel: Control the touch screen control panel

10. Sticky roller: Taiwan custom

11. Ball screw: TBI

12. Number of brushes: 1 pcs

13. Sticky wheel number: 2 pcs

14. Sticky paper roll Quantity: 1 pcs

15. In addition to static equipment: SANYOU (or customer matching)

16. Cylinder: SMC

17. Electrostatic value: ≤ 50V

18. Rack material: 3.0 iron welding, white electrostatic spraying

19. Standard signal: using SMEMA standard 4-core signal cable

#MT-200 PCB Cleaner Catalog #Mactech

0 notes