Electric cables are normally installed on the assumption of a safe working life

Electric cables are normally installed on the assumption of a safe working life of at least 20 years. Changes in the insulating material take place with the passing of time and these changes, which may eventually result in an electrical breakdown, are accelerated at higher temperatures. Thus, if the working life is fixed, the limiting factor is the temperature at which the cable is required to operate.

During operation, the temperature at which the cable will operate depends upon the ambient temperature and the heating effects of the current produced due to the resistance of the cable conductors.

The heat dissipation of buried cables depends on the depth of laying, ground ambient temperature and its thermal resistivity, these being dependent on their geographical location and the season of the year. Nearby cables would also affect the ground temperature. Cables in air reach steady operating temperatures more quickly than similar cables underground and large cables take longer than small ones.

The heat may cause a change in the properties of an insulating material or in extreme cases, deformation may occur. It is important, therefore, to realise that there is “a cable for the job”.

There is a very wide range of cables designed to operate at voltages up to 400 kV. It is not possible to discuss all these in this book, but the reader is referred to a publication, Copper Cables, published by the Copper Development Association.

The majority of cables have copper conductors and in a cable these may vary from a single conductor to stranded construction.

The number of electric wire contained in most common conductors is 3, 7, 19, 37, 61 or 91. Thus, 37/0·083 indicates that the conductor has 37 wires each having a diameter of 0·083 in.

Study of electric cable used for 18 years outdoors in Romania shows that only 2% of original quantity of di-(2-ethylhexyl) phthalate has been lost during service life. Formulation was stabilized with lead stabilizer. Twenty percent of original stabilizer was used and required replacement in recycling process.3

A similar study in Sweden (see formulation in the next section) showed that only 1% of extractable matter was lost during 30-40 years of cable use, material was thermally stable, and mechanical performance measured by elongation changed very little. Experimental studies conducted in laboratory which simulated service life by thermal aging at 80°C and considering activation energy in Arrhenius equation at 95 kJ/mol showed that cables should perform for at least 44 years. The cables collected from field are suitable for recycling with minimal adjustments to formulation. Figure 13.19 shows that stability of insulation has linear relationship with duration of aging. Figure 13.20 shows that changes in elongation are very small.4

Degradation of insulation performance of electric cables is basically evaluated by tests and analyses. Based on the result of equipment qualification tests, subsequent analyses to confirm the integrity after a 60-year service period of cables and the result of insulation resistance measurement and insulation diagnostic tests, it has been concluded that immediate degradation of insulation performance is unlikely to occur for most types of cables.

Degradation of insulation performance is detected by the insulation resistance measurement, insulation diagnostic tests and performance tests of systems and components, which are performed during the inspection.

The Japanese government commenced a national R&D project on cable ageing to have more accurate prediction. Under this project many experiments are being performed to acquire time dependent data of cable ageing. Superposition of the time dependent data proposed by IEC 1244-2 is proposed as a suitable method to predict cable ageing.

The Japanese plant utilities conduct measurement of insulation resistance to monitor degradation of insulation performance and are planning to perform sample investigation to acquire actual degradation data of cable insulations.

An area of rubber cable technology where much research and development work has been concentrated in recent years is that of the behaviour of cables in fires. Although they may overheat when subject to current overloads or mechanical damage, electric cables in themselves do not present a primary fire hazard. However, cables are frequently involved in outbreaks of fire from other causes which can eventually ignite the cables. The result can be the propagation of flames and production of noxious fumes and smoke. This result, added to the fact that cables can be carrying power control circuits which it is essential to protect during a fire to ensure an orderly shutdown of plant and equipment, has led to a large amount of development work by cablemakers. This work has included investigations on a wide range of materials and cable designs, together with the establishment of new test and assessment techniques.

Although PVC is essentially flame retardant, it has been found that, where groups of cables occupy long vertical shafts and there is a substantial airflow, fire can be propagated along the cables. Besides delaying the spread of fire by sealing ducts at spaced intervals, an additional safeguard is the use of cables with reduced flame propagating properties. Attention has also been focused on potential hazards in underground railways, where smoke and toxic fumes could distress passengers and hinder their rescue. Initially, compounds with reduced acidic products of combustion were incorporated in cables which have barrier layers to significantly reduce the smoke generated. In the meantime, other cablemaking materials have been developed which contain no halogens and which also produce low levels of smoke and toxic fumes as well as having reduced flame propagating properties. These are now incorporated in British Standards such as BS 6724 and BS 7211.

A different requirement in many installations, such as in ships, aircraft, nuclear plant and the petrochemical industry (both on and off-shore), is that critical circuits should continue to function during and after a fire. Amongst the cables with excellent fire withstand performance, mineral insulated metal sheathed cables are particularly suited for use in emergency lighting systems and industrial installations where ‘fire survival’ is required. As fire survival requirements on oil rigs and petrochemical plants become more severe, new control cable designs have been developed to meet fire tests at 1000°C for 3h with impact and water spray also applied, and also to have low smoke and low toxic properties.

Another novel approach to fire protection in power stations and warehouses is the use of fire detector cables (Figure 31.4). These are used in a system which both detects and initiates the extinction of a fire in the relatively early stages of its growth. These cables have also been installed in shops, offices and public buildings, where the cables can be used to operate warning lights or alarms.

The starting point is the real-life cable installations, simply because any fire regulation aims at addressing real-life fires. However, realistic cable installations cannot be used in a testing and classification system. The costs will be enormous as the number of different installations is almost infinite. The solution is therefore based on the assumption that certain large-scale reference scenarios can be representative of real-life hazards and that performance requirements of the cables can be identified in these reference scenarios. The term reference scenario is here used for an experimental set-up that is deemed to represent real life.

In exact terms the representation will never be true. However, a reference scenario is created in such a way that experimental fires in the scenario will be representative of a large number of real practical cases sufficiently accurately for a regulator. The burning behaviour of cables in the reference scenarios can then be linked to the burning behaviour in standardised test procedures. This is achieved by analysing fire parameters like heat release rate, flame spread and smoke production from experiments in the reference scenario and comparing them to the standard rate. When this link is established it is possible to use measurements in the standardised tests for classification. Thus the classification of a table in a standard test will reflect a certain burning behaviour in the reference scenario which in turn is linked to real-life hazard situations.

The test used to determine the flame resistance of electric cables, signal cables, and cable splice kits is described in Title 30, Code of Federal Regulations, Part 7, Subpart K (CFR 30, 2005). The principal parts of the apparatus are a test chamber or a rectangular enclosure measuring 17 inches deep by 14 inches high by 39 inches wide (43.2 cm deep by 35.6 cm high by 99.1 cm wide) and open at the top and front. The floor or base of the chamber is lined with a noncombustible material to contain burning matter which may fall from the test specimen during a test. Permanent connections are mounted to the chamber and extend to the sample end location. The connections are used to energize the electric cable and splice specimens. The connections are not used when testing signaling cables. A rack consisting of three metal rods, each measuring approximately 3/16 inch (0.48 cm) in diameter is used to support the specimen during a test. The horizontal portion of the rod which contacts the test specimen shall be approximately 12 inches (30.5 cm) in length. A natural gas type Tirrill burner, with a nominal inside diameter of 3/8 inch (0.95 cm), is used to apply the flame to the test specimen.

For tests of electric cables and splices, a source of either alternating current or direct current is used for heating the power conductors of the test specimen. The current flow through the test specimen is regulated and the open circuit voltage is not to exceed the voltage rating of the test specimen. An instrument is used to monitor the effective value of heating current flow through the power conductors of the specimen. Also, a thermocouple is used to measure conductor temperature while the cable or cable splice kit is being electrically heated to 400 °F (204.4 °C). For the electric cable test, three specimens each three feet (0.91 m) in length are prepared by removing five inches of jacket material and two inches of conductor insulation from both ends of each test specimen.

For splice kits, a splice is prepared in each of three sections of a MSHA-approved flame-resistant cable. The cable used is the type that the splice kit is designed to repair. The finished splice must not exceed 18 inches (45.7 cm) or be less than 6 inches (15.2 cm) in length for test purposes. The spliced cables are three feet in length with the midpoint of the splice located 14 inches (35.6 cm) from one end. Both ends of each of the spliced cables are prepared by removing five inches of jacket material and two inches of conductor insulation. The type, amperage, voltage rating, and construction of the power cable must be compatible with the splice kit design.

The test specimen is centered horizontally in the test chamber on the three rods. The three rods are positioned perpendicular to the longitudinal axis of the test specimen and at the same height. This arrangement permits the tip of the inner cone from the flame of the gas burner to touch the jacket of the test specimen. For splices, the third rod is placed between the splice and the temperature monitoring location at a distance 8 inches (20.3 cm) from the midpoint of the splice. The gas burner is adjusted to produce an overall blue flame five inches (12.7 cm) high with a three-inch (7.6 cm) inner cone and without the persistence of yellow coloration. The power conductors of the test specimen are connected to the current source. The connections must be compatible with the size of the cable's power conductors to reduce contact resistance. The power conductors of the test specimen are energized with an effective heating current value of five times the power conductor ampacity rating at an ambient temperature of 104 °F (40 °C).

The electric current is monitored through the power conductors of the test specimen with the current measuring device. The amount of heating current is adjusted to maintain the proper effective heating current value until the power conductors reach a temperature of 400 °F (204.4 °C). For electric cables, the tip of the inner cone from the flame of the gas burner is applied directly beneath the test specimen for 60 seconds at a location 14 inches (35.6 cm) from one end of the cable and between the supports separated by a 16 inch (40.6 cm) distance. For the splices made from the splice kits, the tip of the inner cone from the flame of a gas burner is applied for 60 seconds beneath the midpoint of the splice jacket. After subjecting the test specimen to the external flame for the specified time, the burner flame is removed from beneath the specimen while simultaneously turning off the heating current. The amount of time the test specimen continues to burn is recorded after the flame from the burner has been removed. The burn time of any material that falls from the test specimen after the flame from the burner has been removed is added to the total duration of flame. The length of burned (charred) area of each test specimen is measured longitudinally along the cable axis. The procedure is repeated for the remaining two specimens. For a cable or splice kit to qualify as flame resistant, the three test specimens must not exceed a duration of burning of 240 seconds and the length of the burned (charred) area must not exceed 6 inches (15.2 cm). The flame test of an electric cable is shown in Fig. 13.4 – the electric cable did not meet the test criteria.

The performance of a centrifugal fan with enlarged impeller

The influence of enlarged impeller in unchanged volute on G4-73 type centrifugal fan performance is investigated in this paper. Comparisons are conducted between the fan with original impeller and two larger impellers with the increments in impeller outlet diameter of 5% and 10% respectively in the numerical and experimental investigations. The internal characteristics are obtained by the numerical simulation, which indicate there is more volute loss in the fan with larger impeller. Experiment results show that the flow rate, total pressure rise, shaft power and sound pressure level have increased, while the efficiency have decreased when the fan operates with larger impeller. Variation equations on the performance of the operation points for the fan with enlarged impellers are suggested. Comparisons between experiment results and the trimming laws show that the trimming laws for usual situation can predict the performance of the enlarged fan impeller with less error for higher flow rate, although the situation of application is not in agreement. The noise frequency analysis shows that higher noise level with the larger impeller fan is caused by the reduced impeller–volute gap.

An implicit, time-accurate 3D Reynolds-averaged Navier-Stokes (RANS) solver is used to simulate the rotating stall phenomenon in a plastic centrifugal fan. The goal of the present work is to shed light on the flow field and particularly the aerodynamic noise at different stall conditions. Aerodynamic characteristics, frequency domain characteristics, and the contours of sound power level under two different stall conditions are discussed in this paper. The results show that, with the decrease of valve opening, the amplitude of full pressure and flow fluctuations tends to be larger and the stall frequency remains the same. The flow field analysis indicates that the area occupied by stall cells expands with the decrease of flow rate. The noise calculation based on the simulation underlines the role of vortex noise after the occurrence of rotating stall, showing that the high noise area rotates along with the stall cell in the circumferential direction.

As the power source of the air and gas system in the thermal power plant, the operation status of the centrifugal fan is directly related to the safe and economic operation of the power plant. Rotating stall in the centrifugal fan is a local instabilities phenomenon in which one or more cells propagate along the blade row in the circumferential direction. The nonuniform flow, the so-called stall cell, rotates as a fraction of the shaft speed, typically between 20% and 70%. This running mode is responsible for strong vibrations which could damage the blades [1]. Meanwhile, it will increase the aerodynamic noise.

In order to reveal the generation mechanism of rotating stall, lots of models and theories have been proposed since the 1960s. Especially, experimental methods were widely used to illustrate the characteristics of internal flow field during stall. Lennemann and Howard discussed the causes of stall cells in low flow rate condition through the hydrogen bubble flow visualization method [2]. Lucius and Brenner experimentally studied the speed variation of a centrifugal pump in rotating stall stage [3]. For the centrifugal turbomachine, multiple factors can affect the characteristics of stall. Vaneless diffuser, for example, has significant influence on stall. Hasmatuchi et al. experimentally investigated the effect of blowing technology on the flow field of a centrifugal pump under rotating stall [4]. Rodgers conducted an experimental research on rotating stall in a centrifugal compressor with a vaneless diffuser and found that the stall margin can be improved through adjusting the expansion pressure factor [5]. Abidogun carried out an experiment to investigate the influence of vaneless diffuser on the stall characteristics. The results showed that increasing the length of diffuser can improve the rotating speed of stall, and the change of width showed no effect on stall [6].

Further efforts were made to study the stall inception in order to avoid the occurrence or minimize the effect of stall. As well accepted, two types of stall inception proposed by Camp and Day modal wave inception and spike inception were investigated experimentally [7]. Leinhos et al. studied development process of stall inception under instantaneous inflow distortion in an axial compressor [8].

With the rapid development of computer technology, numerical simulation has become an important method for flow field research of turbomachine under rotating stall conditions. Gourdain et al. investigated the ability of an unsteady flow solver to simulate the rotating stall phenomenon in an axial compressor and found that it was necessary to take the whole geometry into consideration to correctly predict the stall frequency [1]. Choi et al. investigated the effects of fan speed on rotating stall inception; the results showed that, at 60% speed (subsonic), tip leakage flow spillage occurred successively in the trailing blades of the mis-staggered blades [9]. Zhang et al. numerically studied the stall inception in a centrifugal fan, and the results showed that the stall inception experienced probably 50 rotor cycles developing into a stall group. The inception showed significant modal waveform. The importance of volute for generation of stall inception was illustrated through flow field analysis [10].

Aerodynamic noise is mainly caused by vortex and flow separation. So the unsteady behavior of rotating stall may have an influence on the noise of centrifugal fan. In capturing the physical mechanism of the fan noise associated with rotating stall, the primary work is to characterize the noise. During the 1960s, the interaction between noise and turbulence was discussed by Powell, and the vortex sound theory was proposed to explain the generation of acoustic sound. Then, Lighthill made a breakthrough in aerodynamic noise theory research by proposing the acoustic analogy [11]. Based on these works, Díaz et al. put forward a prediction of the tonal noise generation in an axial flow fan, and the noise level in the plastic centrifugal blower far-field region was estimated by means of acoustic analogy [12]. Scheit et al. analyzed the far-field noise in a metal centrifugal fan with an acoustic analogy method and presented design guidelines to optimize the radiated noise of the impeller [13]. The global control of subsonic axial fan at the blade passing frequency was also discussed by Gérard et al. [14]. He aimed at cancelling the tonal noise by using a single loudspeaker in front of the fan with a single-input-single-output adaptive feedforward controller. According to Ouyang et al.’s work, the far-field noise generated by cross-flow fan with different impellers was measured and it showed the great influence of blade angles on the inflow pattern [15]. Based on the previous research, a new method to predict the fan noise and performance is developed by Lee et al., and through an acoustic analogy, the acoustic pressures from the unsteady force fluctuations of the blades are obtained [16].

In summary, a wide range of flow characteristics on rotating stall in compressor have been investigated and the researches concentrated on stall inception. The present work focuses on two aspects: simulation of the rotating stall phenomenon with a 3D flow solver and seeking the deep physical mechanism of this instability in a centrifugal fan. The numerical method is presented with the model and the particular boundary conditions are used. Results from the whole geometry simulation are then analyzed. In the first part, aerodynamic characteristics and frequency domain characteristics of the centrifugal fan under different stall conditions are analyzed. In the second part, the velocity vector field distributions in the centrifugal fan are discussed. Finally, noise characteristics of the centrifugal fan under different stall conditions are studied. And the noise characteristics during the circumferential propagation of stall cells are also discussed.

2. Centrifugal Fan Description

The configuration of range hood centrifugal fan studied in this work is shown in Figure 1. It is composed of current collector, impeller with 12 airfoil blades, and the volute. The inlet and outlet diameter of the impeller are 568 mm and 800 mm, respectively. The inlet and outlet width of impeller are 271 mm and 200 mm, respectively. The nominal rotation speed is 1450 rpm. The volute tongue gap is 1% of the impeller outlet diameter. The width of the rectangular volute is 520 mm, and a simple antivortex ring is set inside the volute to reduce the generation of vortex. At the design operating point, the volume flow is 6.32 m3/s and the full pressure is 1870 Pa.

As shown in Figure 8(b), under the combining influence of both stall cell and volute tongue, the high noise area is gradually elongated. Due to the propagation of stall cell, it gradually gets away from the area of volute tongue, resulting in weakening the superimposing effect. As time goes by, the high noise area in Figure 8(c) gets further elongated with a trend of separation and the sound power level of high noise areas decreases. In Figure 8(d), the high noise areas corresponding to the vortex noise and volute tongue noise basically separate. And the sound power level corresponding to volute tongue greatly declines.

It can be drawn from Figure 8 that while the impeller passes three passages along clockwise direction, the high noise area passes two impeller passages along the clockwise direction. It indicates that, in the absolute coordinate reference system, the high noise area occupying about three impeller passages rotates in the same direction with impeller under rotating stall. It also has the same speed with stall cells, while in the relative coordinate reference system, high noise area spreads in the opposite direction of the rotation of the impeller.

Through the analysis above, there are two major sources of noise in a centrifugal fan under rotating stall, namely, the vortex noise caused by stall and the volute tongue noise caused by the rotation of impeller. When the stall cell spreads to the volute tongue, due to the superimposing effect of vortex noise and volute tongue noise, the sound power level is the highest and the high noise area is the largest. While the stall cell is away from the volute tongue, the corresponding high noise areas separate gradually. Along with that, the sound power level decreases and the high noise area becomes smaller. Therefore, the aerodynamic noise of the centrifugal fan under rotating stall changes periodically over time, and the fluctuation period is the same with the rotating period of the stall cell.

The authors declare that they have no financial or personal relationships with other people or organizations that can inappropriately influence their work; there is no professional or other personal interests of any nature or kind in any product, service, and/or company that could be construed as influencing the position presented in, or the review of, this paper.

3 Ways Suspended Platforms Increase Efficiency for Vertical-Vessel Maintenance

It’s time to upgrade maintenance practices for vertical vessels. Like any routine maintenance, inspecting, removing and replacing refractory in vertical vessels places a costly burden on facilities in terms of downtime and lost productivity. One of the main reasons for this is the traditional solution for accessing vertical surfaces – scaffolding – severely limits efficiency. It also increases safety risks for employees.

Processing facilities are taking action to reclaim maintenance productivity and safety by investing in custom-manufactured suspended platforms for vertical-vessel operations. These systems feature a lightweight, heavy-duty metal platform that is erected inside the vessel and raised or lowered using manual or electric hoists for hassle-free maintenance and relining applications.

Suspended platforms offer a number of benefits over scaffolding systems, starting with effectively eliminating the protracted setup times that dominate scaffolding-based maintenance schedules. Here’s how these customized systems can boost productivity and safety throughout the maintenance process.

Speedy Setup

The amount of time scaffolding systems take to erect is their biggest deterrent and the greatest drain on maintenance productivity. This is due in part to the sheer complexity of the operation, which includes juggling a variety of pipes, hardware, boards and other materials to create the structure. Erection times vary based on vessel size and configuration, but even with an experienced crew, scaffolding can take several shifts all the way up to an entire week to construct. This puts significant stress on maintenance budgets and timelines.

To simplify the process and decrease setup times, steel suspended platform implement a modular design and pin-together construction. This greatly reduces the number of components and tools required for erection and allows crews to complete setup in as little as two hours.

Modular components manufactured from high-strength 6061-T6 aluminum provide the same strength as steel at one-third of the weight. And, because vertical vessels often feature small access points, manufacturers limit the size of modular components. The resulting pieces are easy to maneuver, weighing 40 pounds (18 kg) or less, and fit through a 22-inch-diameter (560-mm-diameter) access hole. This provides a lighter, more easily maneuverable solution than scaffolding’s heavy wooden planks and steel pipes, some of which are up to 14 feet long.

In addition, pin connections allow for fast assembly and improve platform strength over welded connections by allowing for some flexibility while the platform is being raised or lowered. Welded joints are rigid, which increases stress on risers at platform joints. Pin-together joints are a better solution to help maintain safety and stability when dealing with varying speeds from the climbing hoists.

It is worth noting that suspended platforms require some initial site preparations. This can increase setup times the first go-round – sometimes up to a full shift for complicated systems. But in the long run, a suspended platform can save facilities significant time and effort with each use, leading to significant ROI potential.

For example, a copper plant replaced the scaffold system for their smelter with a custom suspended platform. This increased productivity and safety. Overall, the plant was able to save 320 man-hours per shutdown with the new system.

Room to Move

Even after the platform is assembled, the productivity benefits continue to add up. With scaffolding, tools and materials need to be hoisted up to working height a little at a time, often manually. This is a slow process with a heavy physical toll. It also limits productivity by restricting supply lines for materials, such as refractory brick, gunning equipment or other necessities.

A suspended platform, on the other hand, can easily transport up to 6,000 pounds (2,722 kg) up and down, and the open design provides ample space for personnel, tools and materials. This allows several workers to operate in the same area comfortably, as well as have everything they need close at hand for efficient maintenance. Crews simply load all necessary materials at the start of the shift while the platform is positioned at the vessel’s access point. When more brick or other supplies are required, the crew lowers the platform, loads the necessary materials and then easily returns to height. This saves considerable time and energy and can increase productivity by limiting the number of trips up and down.

The platform also provides more room and easier positioning for equipment such as gunning machines for shotcrete applications. Crews simply set up the machine directly on the platform and maneuver the entire system up and down, eliminating downtime from repositioning while maintaining an ideal distance from the vessel surface for proper adhesion. Using a suspended platform for this application also eliminates the physical toll and risk to crews from heavy hoses hanging from the scaffolding.

In addition, the open platform and electric hoist system allow for infinitely variable height, resulting in unrivaled access for inspection, removal and replacement of refractory materials.

Scaffolding is inherently rigid. It has to be to create a sturdy base of operations. However, this rigidity restricts crew access to the burn surface. Pipes inhibit visual inspection and make it difficult to work on the area directly behind them. The scaffolding structure can also obstruct small flaws, causing them to be overlooked. Crews must squat down or reach up high when working on surfaces in between 8-foot scaffolding stories.

Suspended platforms provide crews with 360-degree access at a comfortable working height, regardless of the task at hand. To optimize accessibility and productivity for a particular facility, manufacturers also customize designs to fit vessels up to 22 feet in diameter, so crews can get directly against the burn surface without risk of falling. This allows crews to inspect every inch, catching even the small flaws that could lead to bigger problems down the line if overlooked. Also, some suspended platforms allow crews to adjust the size of the platform by up to 3 feet while suspended by changing the outer panels. This results in better accessibility and easy transition between different widths of a vessel.

Ergonomics for Better Economics

It goes without saying that having a platform, rather than a narrow scaffold, increases worker safety.

Falls continue to rank number one in workplace injury reports, and refractory repair is not immune to tragic accidents. Recent U.S. Bureau of Labor Statistics data identified 338 fatal falls to the lower level among 1,038 total construction fatalities for the year. That same year, falls on the same level or to lower levels amounted to $17.1 billion (29.2%) of the nearly $60 billion spent by employers on serious, non-fatal workplace injuries.

A suspended platform replaces narrow wooden catwalks with an aluminum surface that spans the entire vessel, eliminating the risk of falls or dropped objects. It also eliminates the need for workers to climb up and down carrying small tools and the need to haul materials and larger equipment up to height, hand over hand, resulting in a much safer jobsite.

There are long-term safety benefits that go beyond this. From setup through all aspects of refractory maintenance, an aluminum suspended platform puts less physical strain on employees. The lightweight, modular components are less cumbersome than long poles and heavy wooden planks. Easy access to materials and tools reduces the risk of repetitive-motion injuries as well as minor cuts, bruises or scrapes that come with manually moving refractory materials. Being able to position the platform at the ideal working height for the job at hand limits bending or reaching, providing an ergonomic solution instead.

All of these small but significant safety benefits lead to long-term savings in the form of worker’s compensation claims and insurance premiums.

Making the switch to a ZLP500 rope suspended platform requires some initial planning, but positive returns are almost immediate. Facilities that have made the switch save tens of thousands of dollars with each maintenance cycle, providing a return on investment in one or two uses. The key is working with a reputable manufacturer that can provide a customized platform that fits a facility’s needs perfectly. Working together, these partners can revolutionize refractory maintenance in vertical vessels.

Mr. Jayesh Vadukiya, M.D, New Age Construction Equipment Engineering Company

New Age Construction Equipment Engineering Company is one of the leading manufacturers of construction equipment like Rope Suspended Working Platforms (Gondolas/ Cradles), Bar Bending Machines, Bar Cutting Machines, etc. The company is strictly complying with ISO 9001:2008 certification and its products have also received CE certificates. The stringent quality standards conforming to “OE” standards enable it to guarantee 100% satisfaction for the entire range of products.

New Age believes in innovation, technology, and customization of its products, based on market research and end-users’ expectations, and has a strong sales & service team of professionals. The company has many instances of innovation and customization, especially of its Rope Suspended Platforms (RSP) / Gondolas/ Cradles. Presenting here two success stories on customized RSP for Dam & Silo Project.

The job was to clean the wall of the dam. It was a very difficult job because of the wind pressure and the height of the wall. The width of the road on the dam was too short to fix a standard upper mechanism of RSP. Another problem was the customer’s requirement of designing the upper mechanism in such a way that vehicles should also pass through the upper mechanism and their movement should not be stopped during the cleaning.

Moreover, the upper mechanism was so heavy that it was next to impossible to shift it. The customer wanted to move the wall machine (upper mechanism + cradle) from one place to another in a short time, and we did that without the help of any laborers.

We designed the RSP in such a way that the client’s requirement was fulfilled, and work was done timely. We had also provided specially designed Motorized device for shifting of wall machine without any requirement of labor. With our vast experience of doing challenging projects, we are always ready to take new assignments and try to resolve all issues through our customized solutions.

Simulation of tin penetration in the float glass process

The flat glass produced by the float glass process has a tin-rich surface due to the contact with molten tin. The penetration of tin into the glass surface is assumed to involve coupled diffusion of stannous (Sn2+) and stannic (Sn4+) ions. The diffusion coefficients of these ions were calculated using the modified Stocks–Einstein relation with the oxidation velocity of stannous ions depending on the oxygen activity in the glass. The ion diffusion was analyzed using a coupled diffusion simulation with a modified diffusion coefficient to compensate for the negative effect of the glass ribbon’s stretching or compressing in the glass forming process. Tin penetration simulations for both green glass and clear glass show an internal local tin concentration maximum in green glass which is quite different from that in clear glass. The local maximum in the profile is associated with the accumulation of stannic ions where the greatest oxygen activity gradient occurs. Since more float time is needed in the manufacture of thicker glass plate, the tin penetrates to a greater depth with the maximum deeper in the glass and the size of the maximum larger for thicker glass.

The float glass process, which was originally developed by Pilkington Brothers in 1959 (Haldimann et al., 2008), is the most common manufacturing process of flat glass sheets. More than 80–85% of the global production of float glass is used in the construction industry (Glass for Europe, 2015a). In the float glass process, the ingredients (silica, lime, soda, etc.) are first blended with cullet (recycled broken glass) and then heated in a furnace to around 1600°C to form molten glass. The molten glass is then fed onto the top of a molten tin bath. A flat glass ribbon of uniform thickness is produced by flowing molten glass on the tin bath under controlled heating. At the end of the tin bath, the glass is slowly cooled down, and is then fed into the annealing lehr for further controlled gradual cooling down. The thickness of the glass ribbon is controlled by changing the speed at which the glass ribbon moves into the annealing lehr. Typically, glass is cut to large sheets of 3 m × 6 m. Flat glass sheets of thickness 2–22 mm are commercially produced from this process. Usually, glass of thickness up to 12 mm is available in the market, and much thicker glass may be available on request. A schematic diagram of the production process of float glass is shown in Fig. 5.2.The float glass process was invented in the 1950s in response to a pressing need for an economical method to create flat glass for automotive as well as architectural applications. Existing flat glass production methods created glass with irregular surfaces; extensive grinding and polishing was needed for many applications. The float glass process involves floating a glass ribbon on a bath of molten tin and creates a smooth surface naturally. Floating is possible because the density of a typical soda-lime-silica glass (~2.3 g/cm3) is much less than that of tin (~6.5 g/cm3) at the process temperature. After cooling and annealing, glass sheets with uniform thicknesses in the ~1–25 mm range and flat surfaces are produced. The ultra clear float glass process is used to produce virtually all window glass as well as mirrors and other items that originate from flat glass. Since float glass is ordinarily soda-lime-silica, the reference temperatures and behavior of this glass are used in the discussion below.

Figure 3.48 shows the basic layout of the clear float glass line. The glass furnace is a horizontal type, as described above. For a float line, the glass furnace is typically on the order of ~150 ft long by 30 ft wide and holds around 1200 tons of glass. To achieve good chemical homogeneity, the glass is heated to ~1550–1600°C in the furnace, but is then brought to about 1100–1200°C in the forehearth. From there, the glass flows through a channel over a refractory lipstone or spout onto the tin bath. As it flows, the glass has a temperature of about 1050°C and viscosity of about 1000 Paradical dots. A device, called a tweel, meters the flow of the molten glass.Imperfections include bubbles (or ‘seeds’) that may have a number of possible sources, the most common being gas evolved during firing. Bubbles may contain crystalline materials formed during cooling of the glass that may provide clues to the origin of the bubbles. Cords are linear features within the glass that may result either from imperfectly homogenized raw materials, dissolved refractories or devitrified material. Figure 360 shows the appearance of soda–lime–silica glass that exhibits bubbles and cords. ‘Stones’ are solid crystalline substances occurring in glass that are regarded as defects. They are usually derived either from the batch material, refractories, or devitrification. Figure 361 shows the appearance of soda–lime–silica glass that contains a devitrification ‘stone’. These may develop as the result of incomplete mixing of the molten glass constituents and/or too low a firing temperature. The ‘stone’ shown in Figure 361 contains an aggregation of tridymite crystals (see 362).

As the floating glass ribbon traverses down the length of the tin bath, its properties change dramatically. The glass enters as a viscous liquid and exits virtually a solid at a temperature very close to its glass transition temperature. The details of how the temperature changes and the viscosity builds are complicated. On one side, the free surface of the glass is exposed the atmosphere; heat can leave this surface by radiation or convection. Cooling and heating apparatuses are stationed above the glass ribbon down the length of the bath to allow adjustment of the ribbon temperature. On the other side, the glass is in contact with the tin bath, which can absorb some of the heat and transport it away from the ribbon. The tin bath is in constant motion due to the moving glass above it as well as the thermal convection currents. Unfortunately, no simple approximations can be made to make the modeling of the heat transfer.

The thickness of the tinted float glass sheet is adjusted by controlling flow onto the tin bath as well as by tension exerted along the length of the bath by rollers in the annealing lehr and sometimes by rollers in the bath unit itself. In the Pilkington design, the melt enters the bath and spreads out laterally to a thickness near the equilibrium value. If a sheet thicker than the equilibrium is required, then this spreading is constrained with physical barriers. If a sheet thinner than equilibrium is needed. then the glass ribbon is pulled in tension by rollers. In the PPG design, thickness is regulated by the tweel position and by tension from rollers in the lehr. The thermal profile allows the thinning deformation to take place effectively. A short distance away from the entry point, the temperature of the ribbon drops and the viscosity rises. Overhead coolers help this process. The glass viscosity is high enough so that knurled rollers contact the glass ribbon and pull it forward (and in some operations, laterally as well). Heaters are placed shortly downstream of these edge rollers to raise the temperature of the ribbon and create a deformable zone. This zone is followed by coolers that again lower the temperature and raise the viscosity. At exit from the lehr, the ribbon is virtually solid. The main deformation is due to the rollers in the lehr, which pull on the glass ribbon from the lehr to the edge rollers; extension takes place in the deformation zone. Example 3.15 considers the exit velocity of glass from the process.

For many years, however, the glass industry has been trying to solve a problem which affects almost every building in the world. How do you maintain the fundamental characteristics of glass, such as optical clarity and external esthetics without constant and costly maintenance? Whether the building is for commercial or residential use, the one constant requirement is for regular cleaning to be undertaken to ensure the glass maintains its optimum appearance.

The challenge for the glass industry is increased as a result of architects finding ever more resourceful and novel uses for glass. The use of glass in atria and overhead glazing can sometimes result in complex areas, which can make maintenance more difficult.

In addition to the esthetic issues it is a well-known phenomenon that if glass is not cleaned regularly then over a period of time the glass can weather, which makes it almost impossible to restore its esthetic properties. In extreme circumstances this can lead to the glass needing replacement.

The process of cleaning windows can also lead to safety and environmental issues. Window cleaning generally involves the use of portable ladders for cleaning windows on ground, first, and second floors. Figures for accidents reported to the Health and Safety Executive (HSE) and local authorities reveal that unfortunately between two and seven window cleaners have been killed every year in Great Britain and around 20–30 suffer major injuries due to falls involving ladders. From an environmental aspect window cleaning can involve the use of harsh chemicals. These are often washed off during the cleaning process and can ultimately lead to ground contamination.

Recently, self-cleaning coatings have been developed, which are designed to reduce the amount of maintenance required by working with the forces of nature to clean dirt from the glass. These coatings are based on a well-known metal oxide called titanium dioxide, which is regularly used in paints, toothpaste, and sunscreens.

Tin is an ideal bath material because it has the right set of physical properties. Tin melts at 232°C, has relatively low volatility, and does not boil until over 2000°C. Molten tin is denser than molten glass and is not miscible or reactive with molten glass. The gas atmosphere is controlled so that tin does not oxidize at a fast rate. Any oxide that does form is collected in a dross container on the bath.

Regulating the flow of the wired glass is important at this stage, both from the entry point and the lateral flow. The glass flow onto the tin bath is regulated by a gate, called a tweel, which is located in the canal between the forehearth and spout. The glass flows down the spout or lipstone onto the tin surface. There is some pressure driving this flow through the gap of the tweel. See Example 3.14. As the glass flows onto the tin bath, the thickness of the glass sheet depends on how that flow is controlled laterally and along the length of the bath. The first step to understanding thickness control is to examine the equilibrium thickness.

A review on the durability of PVC sewer pipes

Polyvinyl chloride (PVC) has become one of the dominant construction materials for sewer systems over the past decades, as a result of its reputed merits. However, since PVC sewer pipes have operated for decades in a hostile environment, concern over their longevity has been lately raised by sewer managers in the Netherlands. Towards that direction, the main factors and mechanisms that affect a PVC pipe’s lifetime are discussed in this article, along with the current lifetime prediction methods and their limitations. The review of relevant case studies indicates that material degradation, if any, occurs slowly. However, inspection (CCTV) data of three Dutch municipalities reveals that severe defects have already surfaced and degradation evolves at an unexpected fast rate. A main reason of this gap between literature and practice is the fact that comprehensive material testing of PVC sewer pipes is rarely found in the literature although it proves to be essential in order to trustfully assess the level of degradation and its origins.

Plastics are used for a wide range of commercial and industrial piping applications. The most known are polyvinyl chloride (PVC), polyethylene (PE), polypropylene (PP), acrylonitrile–butadiene–styrene (ABS), polybutylene (PB) and glass–fibre-reinforced polyester (GRP or FRP). Concerning piping systems for drinking water supply, gas distribution and sewage disposal, PVC, PE and PP are the most popular polymer materials (PlasticsEurope, 2017). Especially for gravity sewer pipes, PVC has been extensively used over the past decades and has become the dominant construction material. Cost efficiency, ease of installation, range of available diameters (40–630 mm) and its reputed chemical resistance favour its wide acceptance by decision makers in urban drainage (Davidovski, 2016).

Since there are PVC sewer pipes in operation for at least four decades, concern over their longevity has been lately raised in the Netherlands. It is still unknown whether the expectations of long-lasting PVC pipes (Folkman, 2014) will prove realistic or new asset management strategies should be established in the near future. Knowledge of the current structural integrity of sewer systems is a key issue for establishing successful asset management strategies, leading to better decision making and more affordable investments. In practice, sewer managers currently base their strategies mainly on visual (CCTV) inspections (Van Riel, Langeveld, Herder, & Clemens, 2014). Subsequently, decisions are taken whether replacement, rehabilitation or a near future inspection should take place. However, linking the observed defects in CCTV to the actual physical state of a pipe is challenging (Van Riel, 2017). A necessary condition for achieving this is comprehensive understanding of the mechanisms that affect a PVC pipe’s lifetime, their combined effects and eventually their results, which are the defects found in practice. An overview of these mechanisms and their origins is included in this article. Lifetime prediction methods for UPVC pipes are also utilised to describe specific types of failure, while their ability to provide trustful lifetime prediction is discussed.

The main aim of this article is to present case studies of PVC sewer pipes found in the literature and to compare the derived conclusions on PVC durability with findings in inspection (CCTV) data. Emphasis is given on the studies that investigate the properties that define the structural integrity and overall performance of a sewer system. The inspection data concerns three different municipalities in The Netherlands: Almere, Amstelveen and Breda. The main discrepancies between literature and inspection data are discussed, as a step towards bridging results from scientific research and observations from practice.

Suspension polymerisation is the most applied process for PVC particles production (80%), whereas emulsion and mass polymerisation provide 12 and 8% of the world production, respectively (Fischer, Schmitt, Porth, Allsopp, & Vianello, 2014). Although the specific details of the PVC particles size slightly differ in the literature (Benjamin, 1980; Butters, 1982; Faulkner, 1975), the microstructure follows the same pattern. This can be described in three stages (Butters, 1982): the stage III-PVC particle (∼100–150 μm), the stage II-primary particle (∼0.1–2 μm) and the stage I particle (∼10 nm). The conversion of the material to a homogeneous product requires that the boundaries of the primary particles disappear and a new continuous entanglement network is developed (Visser, 2009). This procedure is known as the gelation process and its quality is expressed by the gelation level. There are several methods to obtain information about the gelation level (Castillo, 2016; Choi, Lynch, Rudin, Teh, & Batiste, 1992; Fillot, Hajji, Gauthier, & Masenelli-Varlot, 2006; Gilbert & Vyvoda, 1981; Gramann, Cruz, & Ralston, 2010; Johansson & Törnell, 1986; Kim, Cotterell, & Mai, 1987; Marshall & Birch, 1982; Real, João, Pimenta, & Diogo, 2018; Terselius, Jansson, & Bystedt, 1981; Van der Heuvel, 1982).

A general accepted opinion suggests optimum gelation levels of 60–85% (Benjamin, 1980; Breen, 2006). A temperature of >250 °C is needed for this purpose (Guerrero & Keller, 1981), much higher than the degradation temperature of PVC which is ∼205 °C (Wypych, 2015). Due to this fact, thermal energy is complemented with mechanical energy (high shear stresses) by the use of twin rotating screws, so as to accelerate this process without extensive exposure of the material to high temperatures (Visser, 2009). Subsequently, the molten material is introduced in a die so that the final pipe is shaped and cooled. This manufacturing technique is called extrusion and is extensively used to form pipes. Fittings, such as joints, are formed by the injection moulding technique. In the injection moulding process, the melted plastic is injected in a mould, which gives the desired form to the PVC fitting, and after cooling the product is ejected.

During the production process, several additives and fillers may be incorporated in the polymers structure in order to enhance its chemical and physical properties, respectively. Plasticisers and stabilisers are the main additives as they affect the behaviour and degradation rate of the material through its lifecycle. Plasticisers are utilised in order to replace some monomers of the polymer chain, offering a higher degree of mobility and, hence, more flexibility. For sewer applications unplasticised rigid PVC pipes are used. Stabilisers are added for increased resistance to e.g.: UV rays, chemical attack and other relevant external factors (Cardarelli, 2008). For pvc pipework in Europe, lead has been used until the early 2000s, when it was replaced by calcium-based stabilisers in most countries (Anders, 2014).

Every step within the production of PVC pipes and furniture PVC fittings can have an effect on the long-term performance of the final product. The levels of water and oxygen during polymerisation could influence the formation and quality of the produced PVC particles (Butters, 1982). Subsequently, the gelation process, already affected by the degree of polymerisation (Fujiyama & Kondou, 2004), plays a major role in the mechanical properties (Mandell, Darwish, & McGarry, 1982; Moghri, Garmabi, & Akbarian, 2003; Truss, 1985; Van der Heuvel, 1982). These properties are determined by the morphology of the material (Benjamin, 1980; Kuriyama, Narisawa, Shina, & Kotaki, 1998) and by the polymer’s orientation and molecular mobility (Fillot, Hajji, Gauthier, & Masenelli-Varlot, 2007). Additionally, impurities and voids in the polymer structure, frequently referred to as inherent defects, are introduced during production, resulting in crack initiators, and their presence seems to be inevitable (Johansson & Törnell, 1987). The wear observed at the polymer pipes extruders (Gladchenko, Shevelya, Kiyanitsa, & Derkach, 1997) might also contribute to the occurrence of inherent defects.

Residual stresses are also introduced during production, as a result of different cooling rates between the inner and the outer pipe surface (Siegmann, Buchman, & Kenig, 1981), and constitute another parameter that affects the mechanical properties of the produced pipe (Siegmann, Buchman, & Kenig, 1982). Relevant research on residual stresses in PVC pipes (Breen, 2006; Meerman, 2008; Scholten, van der Stok, Gerets, Wenzel, & Boege, 2016) has revealed that their magnitude is in a range of 0.9–4.8 MPa for tensile and 3.9–9.4 for compressive stresses (Table 1). In principle, a faster cooling rate or a thicker pipe wall thickness will lead to higher levels of residual stresses (Janson, 2003; Scholten et al., 2016). However, irrespective of their magnitude, residual stresses affect the crack propagation as they change the stress profile through the pipe (Burn, 1992; Chaoui, Chudnovsky, & Moet, 1987), increase the brittle–ductile temperature (Scholten et al., 2016), and, consequently, they seem to have a tremendous effect on the lifetime of pressurised plastic pipes (Hutař et al., 2013; Poduška et al., 2016).

Metal Forging Tools and Equipment and Parts Supplies

This article discusses the significant factors in the selection of forging equipment for a particular process. It describes the characteristics of forging hydraulic presses, mechanical presses, screw presses, and hammers. The article discusses the significant characteristics of these machines that comprise all machine design and performance data, which are pertinent to the economic use of the machines, including the characteristics for load and energy, time-related characteristics, and characteristics for accuracy.

The forging of metals and alloys is one of the oldest metal forming techniques used by humankind. Forging processes were improved over the centuries and are still being refined. Today, we are certain that there is no limit to these improvements and that we will never reach the point when we can say that nothing more is to be done. Despite the enormous knowledge and experience gained over the centuries, we still face new challenges arising from civilizational progress. One of them is the necessity to produce parts that are more and more complex in terms of shape and properties, which requires not only a deep insight into phenomena that accompany forging processes, but also the development of new techniques, riveting machine and equipment, materials, research methods, and tools, as well as the improvement of the existing ones. With the Special Issue on “Forging Processes of Materials”, the Editorial Board of Materials offers authors the possibility of presenting their findings in this field. As the Guest Editor for the Special Issue, I would like to invite you to contribute to this publication, which, I hope, will serve as a source of knowledge for both theoreticians and practitioners. Hence, I encourage authors to submit papers exploring, in a broad sense, the theory and practice of forging metals and alloys. I wish to assure you that we will make every effort to ensure the highest quality of this Special Issue.

Forging is a hot or cold metal deformation process used to produce metal parts where strength is a paramount concern, engine connecting rods and hand tools being two such examples. The process itself involves using compressive forces to mold and deform metal into the desired shape. For most applications, forging entails heating the base metal until it is malleable enough to work with, although cold and warm forging are also done.

The forge, sometimes called a hearth, is the component that heats the metal prior to forming. In its most fundamental form, forging can be understood in the manner of making horseshoes. The blacksmith heats the metal in the hearth, then pounds it with a hammer against an anvil to flatten it, curve it, pierce it, and generally shape it, repeatedly reheating the metal to maintain plasticity. Small gas-fired forges are available for blacksmiths though many forgers choose to build their own.

Modern industrial forging relies on sophisticated, heavy-duty equipment capable of producing small accurate parts as well as large pieces weighing many tons. As with castings and weldments, many forgings are machined after they are made to achieve their final forms.

An anvil is a large slab of metal, usually made of steel, which serves as the workbench for the blacksmith or automated hydraulic closed die forging hammer device. The metal is placed on the anvil, where it is hammered into the correct shape. Anvils traditionally provide a flat hammering surface, though curved anvil tops are available. A hardy hole and punch hole can sometimes be found on an anvil – the hardy hole serves as the square socket for accepting the shank of a hardy, an interchangeable tool in a variety of shapes used for cutoff, bending, etc. The punch hole provides clearance for punching holes in the metal.

Chisels

Chisels are cutting supplies that chip away at metal. They are traditionally made of high-carbon steel and consist of a long octagonal cross-section with a tapered cutting edge on one end. There are two types of chisels—hot chisels and cold chisels. Cold chisels are typically thinner in construction, and better suited for cold forging. Hot chisels, on the other hand, assist in hot forging processes. Chisels are traditionally applicable in manual forging applications.

Tongs

Tongs assist in the transportation of the heated metal from the forge to the anvil. Many different tong shapes are available to provide adequate gripping of multiple metal shapes and sizes.

Fullers

Forming tools that create grooves or indentions in the forging process are known as fullers. Fullers also help round out corners and stretch the metal. Traditionally used in pairs, fullers work through placing one beneath the metal, and the other on top. This enables the indentation of both sides of the metal component to occur simultaneously.

Forging Hammers

Different forging processes are appropriate for different applications—options such as hot forging, cold forging, closed die forging, upset forging, and press forging are simply a few examples. Many of these forging processes require the use of a hammer to enable compression and shaping of the metal. Forging hammers vary in shape, size, and material based on the particular application, but all industrial hammers typically apply force with a large ram. Two basic types of hammers are:

Drop hammers: Gravity allows the heavy ram to fall onto the metal.

Power hammers: Compressed air, hydraulics, or electricity drive the hammer.

Hammers are capable of delivering percussive impact blows with forces of up to 50,000 lbs. in their largest incarnations, with smaller capacity units also available. For increased forging forces, forgers turn to presses.

Forging Presses

A forging press creates force through mechanical or hydraulic energy without relying on the weight of a hammer and the assistance of gravity to pound metal into the desired shape. Whereas hammers shape a localized portion of the metal, a forging press can forge the entire product at once in a process known as closed-die forging. Forging presses also duplicate the action of hammers in the open die forging process. Both horizontal and vertical forging presses are available. The horizontal presses are called upsetters. Two types of forging presses include:

Mechanical forging press: A mechanical device (often a crank) propels a motor-driven flywheel, forcing the ram against the metal. Mechanical presses are not suited for forging large or complex items but are beneficial in applications that require simple shaping effects. They are capable of producing forces of up to 20,000 tons.

Hydraulic forging press: High-pressure fluid propelled by hydraulic pumps forces the ram against the metal. Hydraulic presses can provide higher forces than mechanical presses, and are sometimes preferred for applications that create large or complex components. Small hydraulic presses are available for blacksmithing operations with forces starting around 10 tons and they grow increasingly more forceful from there, with some very large presses operating in the 50,000-ton range and beyond.

Forging Dies

Forging presses used for closed-die forging require forging dies to properly mold the metal. Dies act as molds into which the hot, malleable metal is pressed. Since dies are unique to each forging project, they are expensive and can lead to high set-up costs prior to forging – forging with dies is best suited for moderate to large production runs. There are two main types of forging dies:

Open die: Open dies are akin to the blacksmith’s hammer and anvil and are usually available in shapes that accomplish specific tasks such as squaring. They do not completely encase the metal, providing free flow everywhere except where the metal meets the die. Open die forging is a good choice for custom metalworking applications as it can be used to produce as few as a single forging. It is also useful in forging very large parts. Where a blacksmith might use tongs to grapple the hot metal forging, many larger forgings are handled by mechanical manipulators because of their immense weight. Open die forging depends a great deal on the skill of the forger to produce the desired shapes. In addition to producing stepped shafting, rings, and cylindrical hollows, open die forging is often used to produce the hemispherical ends of pressure vessels.

Closed die: Here, the metal is completely encased. When the CNC hydraulic die forging hammer or press pushes against the metal, the metal flows and fills the die cavity or cavities. Typically, the pre-forged part will have some resemblance to the final forging before it is placed in the die, preformed by a series of so-called blocker dies.

Summary

This article presents a brief discussion of metal forging tools and equipment. For more information on other products, consult our other guides or visit the Thomas Supplier Discovery Platform to locate potential sources. More information on forging and forging equipment may be found at the Forging Industry Association website.

Modern science and industry have accumulated many efficient methods of forming by hammer forging, such as setting with shift or torsion, sectional forging, expansion by rolls etc. However, they are difficult for realization on forging equipment, what hampers their adoption in industry. Hence technological conservatism in forging. Even state-off-the-art forging complexes have brought no fundamental change into the hammer forging process.

Within the present work we have developed a new composition structure of a forging machine suitable for conventional operations of hammer forging as well as for new operations, unusual for hammer and press forging. The structure of the machine, hereinafter referred to as an automated forging center (AFC) permits to solve the problems of combining external forces, producing new shapes of deformation zones, efficient use of the tool magazine.

Physical and mathematical simulation of technological operations have been carried out to estimate forming and forse parameters, some results being presented in the paper.

Best Wine Glasses of 2020

As if learning the vocabulary, geography, and producers in the wine world isn’t challenging enough, there are also different types of glassware—and figuring out the best wine glasses is no small feat. In the last couple of decades, glass manufacturers have made a killing off of creating dozens of glassware lines and convincing wine drinkers we need multiple types of glasses to be serious about wine. Although the glassware section of my book, Wine for Normal People, wound up on the cutting room floor, this is a topic my podcast listeners love to ask about and one I was excited to reexamine.

I guess we should start with the most important question: Does a glass really make a difference to a wine’s taste? After copious research and testing, I can tell you that glassware does matter to your enjoyment of wine. Certain glass shapes and materials do enhance wine’s aroma and flavor—and some even detract from it! I tested several highly regarded wine glasses and found the best premium, mid-tier, and affordable options for all kinds of wine drinkers.

Ahead, discover all the winners and a thorough breakdown of our testing methods. We’ve also included a primer on the merits of different liquor glass shapes.

Zalto is widely considered the gold standard of glassware by wine connoisseurs and professionals alike. It is made of mouth blown, nonleaded crystal; it’s incredibly light; and it’s shaped like a piece of art. It’s beyond fragile and using this glass is a bit unnerving, but in test after test with wine after wine, it not only allowed the wine to express itself, but in many cases it made the wine taste better than all the other glasses.

From white and red Burgundy to white and red Bordeaux, Italian white to California rosé, Chilean Pinot Noir to Spanish Rioja, the Zalto glass improved the naturally occurring aromas and flavors of each wine effortlessly. But to go a step further, the amazing thing about the Zalto is that it seems to elevate the wine’s subtleties and nuances, introducing new or stronger positive aromas and flavors that the other glasses don’t. For instance, you may get notes of an old medieval church incense and black pepper in a northern Rhône Syrah with the Zalto, but just an herbal note from other glasses (I know it’s crazy but it’s true).

The experience of swirling with Zalto is unlike any other—the lightweight construction and virtually spill-proof bowl (it tapers significantly) made for the most effortless spin, allowing for great aeration and giving it huge points for ease of use. The tapering at the top made every wine’s aromas shine so completely, to the point where the wines felt actually transformed and seemed to transcend themselves.

Although this is technically a Burgundy glass, I found that it improved a variety of wines almost universally. In a lineup of 10 glasses, even done blindfolded, this glass over-performed on experience, flavor, aroma, and comfort. Although the delicate quality of these glasses had me a bit stressed with each use and especially each (hand) wash, it wasn’t enough to deter me from grabbing it over every other glass, every night. It is, despite its fragility, the undisputed best wine glass you can get for your wine.

Because it is so expensive, we recommend just the Burgundy glass as the one you need, but if you have some extra change lying around and drink white wine, pick up those too.

Okay, so, it’s no Zalto, but the Riedel Veritas is half the cost and was a consistent runner-up in test after test. This glass is still fragile thanks to a spindly stem the company has become known for, but the leaded crystal has a slightly sturdier construction than the Zalto while still boasting a narrow rim that feels luxurious and comfortable for sipping.

The Pinot Noir glass did equally well with red Burgundy, Nebbiolo, Bordeaux and more tannic reds. Fuller whites were even slightly better in this one than in the Zalto. The white wine glass enhances the aromas of German Riesling, Italian whites like Fiano, and New Zealand Sauvignon Blanc.

The Veritas does exactly what a great glass should do: allow ample swirling room and enhance the wine’s natural characteristics for both the white glass and the red. The difference between this and the Zalto, for reds specifically, is that the Veritas doesn’t add the nuance and subtleties the Zalto does. It doesn’t improve the wine or allow the more intricate notes to come out. But what it lacks in whatever magic of the Zalto is, it makes up for in affordability and the fact that this glass is less nerve-racking to drink from. That said, Riedel claims these are dishwasher-safe, but unless you plan to make these stemless glasses (My take on that below!), the stem is imminently breakable. These have to be hand-washed.

This little glass (the company is owned by Riedel now, though it was once their biggest competition!) outperformed much more expensive glasses with its thin lip, excellent bowl for swirling, and ability to concentrate aromas. The red and white glasses are thin, but felt sturdy enough that I never worried about breaking them. They go into the dishwasher and come out in one piece. For the money, these glasses are the little engine that could. They came in third or fourth place in tasting every single wine—from Nebbiolo to Malbec, Chardonnay to Grüner Veltliner. This is an elegant everyday glass and it blows away its competitors (Schott-Zwiesel, Stozle, Libbey, and the more expensive Gabriel-Glas). I will warn that although the white glass is spectacular, it is quite small in comparison to the Burgundy glass. It works great, but it can be surprising when you open it, especially in comparison to the ample size of the brandy glass.

You don’t need a glass for every region or grape but depending on what and how you drink, there are four standard glass shapes you should consider. The combination of these shapes plus the cost, fragility, washability, and comfort in holding and drinking will be the keys to getting the best wine glass for you.

The White Wine Glass

Shaped like a tulip, this glass has a round bowl and goes straight up before tapering slightly at the top. The bottom of the glass allows you to swirl without spilling, but the real magic of a white wine glass is that it concentrates aromas of the wine at the rim and traps them slightly so we can sniff the (hopefully) delicious things the wine has to offer.

The standard white glass is a bit smaller than the red: Because whites don’t need as much aeration (swirling), they’re smaller. Also, whites are almost always served colder than reds. Pouring smaller quantities into the glass will ensure that what you have in the glass always stays at a cool temperature. This Vodka glass type will work for almost all white wines, except for fuller whites like oaked Chardonnay and white blends from the Rhône Valley, for example.

Shaped a bit like an upside-down mushroom, these glasses have wide bowls and then taper at the top to a narrow rim. The huge bowl allows for tons of swirling. With reds and the fuller whites, you want to introduce a lot of air into the wine. The swirling motion jostles the esters and aldehydes in wines, which are the things that make the juice smell so good. In very aromatic but less mouth-drying tannic reds, you want to concentrate the aromas at the rim of the glass to maximize the intensity of smell compounds your nose can sense. The wider base allows room to swirl (you should never fill these glasses above the bulge in the glass or it’s spill city), but the top ensures that delicate aromas of red Burgundy (Pinot Noir), Beaujolais (Gamay), or Nebbiolo, for instance, aren’t lost.

The Bordeaux Glass

This is a giant version of the tulip shape we find in the white wine glass, although it tapers less at the top. The relatively straight sides of this glass and large bowl allow air to penetrate before, during, and after swirling, allowing harsh tannins to dance with the oxygen and soften up—exactly what you need to enjoy a Cabernet Sauvignon, a Bordeaux blend, a Rioja from Spain, or a Syrah from the northern Rhône of France.

The Champagne Flute

This is actually quite a controversial opinion among wine snobs: Flutes are festive, fun, and they do, in fact, help keep the sparkle in your glass for longer. There are some practical issues with these party-perfect glasses: Unless you drink sparkling wine a lot, they tend to gather dust; if you have a beak like mine, that can be an issue for drinking; and—the dork argument—they have no room for swirling. Nevertheless, I love enjoying sparkling out of them and I drink enough of it to have them around. Still, they are optional. A white wine glass works just as well.

What About Universal Wine Glasses?

Try as they might, over and over again, the universal glass always makes one wine or another a loser. They are too narrow for tannic reds and sometimes don’t aerate the wine as much as they should. They are too wide and open for aromatic reds or delicate whites (although they are better for whites than reds most of the time). Regardless of how high-quality the glass, the shape matters too much for these glasses to work for all wine types. My advice: Buy a set of whites and reds (I think Burgundy glasses are more useful than Bordeaux) and leave the universals to people who didn’t read this article.

What About Stemless Wine Glasses?

We did not include any stemless glasses in our tests of the best red wine glass simply because we do not feel they belong in that elevated tier. Because there is no stem, the drinker holds the bowl of the glass in their hand—and that direct contact can possibly increase the temperature of the wine, and that increase in temperature can mess up the flavor of the wine.

Stress Distribution at the Fillet of an Internal Flange

This paper deals with the determination of the stress distribution at the fillet of a ANSI B16.5 flanges attached internally to a hollow cylinder. A load parallel to the axis of the cylinder and of variable eccentricity acts on a bearing plate which rests on the flange. The strains are measured by means of electrical resistance wire strain gages. The ratios of the mean cylinder diameter to the cylinder wall thickness and of the mean cylinder diameter to the flange thickness are varied. The principal stresses at the fillet are given as functions of these parameters. The experimental results are compared with the stresses calculated on the basis of an approximate theoretical solution for both an axial and an eccentric load.

Abstract Joining of steel pipes and pipe flanges use today the conventional method of fusion welding, where the flange is girth-welded onto the pipe. However, fusion welding of flanges to pipes is associated with many disadvantages such as the final quality of the weld, degradation of the mechanical properties of the base pipe near the heat affected zone, defects and cracks appearing in the weld, misalignments, to mention a few. The current study proposes a novel pipe-flange connection to replace the fusion welding process of steel pipes with a method based on cold working. The method is based on that the steel pipe is inserted into the neck of the flange, in which two circumferential grooves are manufactured. An expansion tool having two teeth is entered from the open side of the connection and is expanded hydraulically such that the teeth deform the pipe and cold work it plastically into the grooves. This will provide a strong joint between the flange and pipe. In this study the performance of the connection is maximized by optimizing the design of the flange and the expansion tool.

The use of bolted flange connections in the offshore wind industry has steeply risen in the last few years. This trend is because of failings observed in other modes of joints such as grouted joints, coupled with enormous economic losses associated with such failures. As many aspects of bolted flange connections for the offshore wind industry are yet to be understood in full, the current study undertakes a comprehensive review of the lessons learned about bolted connections from a range of industries such as nuclear, aerospace, and onshore wind for application in offshore wind industry. Subsequently, the collected information could be used to effectively address and investigate ways to improve bolted flange connections in the offshore wind industry. As monopiles constitute an overwhelming majority of foundation types used in the current offshore wind market, this work focusses on large ANSI welding neck flanges in the primary load path of a wind turbine foundation, such as those typically found at the base of turbine towers, or at monopile to transition piece connections. Finally, a summary of issues associated with flanges as well as bolted connections is provided, and insights are recommended on the direction to be followed to address these concerns.

As per recent reports, the offshore wind sector could bring in £17.5 bn investment to the U.K. economy over the next few years after faster than expected cost-cutting slashed subsidies for the technology by half [1]. On top of that, the baseline scenario for the United Kingdom’s installations by the end of 2030 is to reach the capacity levels of 40 GW, four times the current state [2]. Additionally, the target of £100 per MWh set for the year 2020 regarding the levelised cost of energy (LCOE) of offshore wind was achieved in U.K. projects four years earlier in 2016 [3]. The above figures reinforce the need for new technological developments that will enable the utilisation of larger and more efficient offshore wind turbines (OWTs). In this direction, one of the most important concerns is the support structure of the turbine’s tower, which requires further study concerning not only the feasibility of future installations, but also current problems that need to be better understood and addressed.

OWT structures, which are quite large in thickness and diameter, operate in the hostile marine environment, where variable amplitude loads are constantly applied on different parts of the structure [4,5]. In the offshore industry, grouted connections were initially used to charge the transition piece (TP), with a certain overlap length, on the monopile (MP) foundations. Therefore, there is a tube-in-tube connection, wherein the space between the two tubes is filled with grout (Figure 1) [6]. Towards the end of last decade, numerous grouted connection joints between large diameter monopiles and connecting tubular steel transition pieces at the base of overlying support towers were found to be failing. For the majority of U.K. offshore MPs that experienced grout cracking and failures, the issue was recognised to be primarily owing to the widespread absence of shear keys (or weld beads) on straight MP and TP surfaces. Bending moments as a result of complex wind (which was the main difference in loading conditions compared with oil and gas platforms) and wave loading were important design considerations that were not accounted for during design of grouted connections for OWTs. Furthermore, axial connection capacity was found to be significantly lower than that assumed previously owing to the MP scale effect, lack of manufacturing and installation tolerances, and abrasive wear due to the sliding of contact surfaces when subjected to large moments. Typical failure modes included dis-bonding, cracking, wear, and compressive grout crushing failure.

The number of bolts depends on the ANSI plate flanges radius and thickness, type of tool used, size of the bolts, and predicted loads on the structure. These bolts serve the purpose of exerting a clamping force to keep the joint together [20]. The behaviour and life of the bolted joint depend on the magnitude and stability of that clamping force. The preload is created by the tightening process during the assembly of bolt and nut in the joint to provide enough clamping force on the joint. Therefore, the bolts need to be preloaded at the assembly stage in the flange connection. An intuitive analogy would be to think of the bolts and the joint members as elastic parts. In that way, they can be modelled as spring elements, where the bolts are stretched in their elastic region when tightened, in order to compress the joint. The joint has a much stiffer elastic constant compared with the bolts, depending on material and dimensions.

It is possible to consider the bolt as an energy storage device, which accumulates the necessary potential energy to clamp the joint and is subjected to several environmental and operative conditions that may affect its behaviour [20]. The objective is for the preload on the bolt to be maintained at a certain level, but, owing to a large number of influencing factors, it is almost impossible to achieve or retain the desired state. It must be noted though, that the main concern is not the value of preload on the bolt, but maintaining the sufficient level of clamping force that holds the joint together. Moreover, if the clamping force is too low, the joint could loosen and be subjected to more severe consequences owing to cyclic loads. On the other hand, if the bolt is over-tight, it could exceed its proof load and may break under external load. In fact, during the tightening process, a torque is applied to turn the nut and the bolt stretches. This operation creates preload in the bolted joint. This sequence of events, at any point, controls the preload. It is possible to control the preload through torque or turn or stretch or through a combination of all of them. In all of the control strategies, the torque is used to tighten the fastener even if other mechanisms are used to control the tightening. There are a lot of uncertainties in the relationship between the control parameters like torque and the preload, which could be minimised by measuring and controlling the build-up of bolt tension. This is the motivation for creating the family of tools called bolt tensioners. Using the bolt tensioner is nowadays a common practice during the installation of offshore wind turbines.

The employment of ANSI blind flanges connections for OWTs has considerably increased in the past decade owing to the failures and subsequent economic losses associated with grouted connections. In this study, the issues and opportunities associated with bolted flange connections have been thoroughly reviewed and discussed for application in the offshore wind industry. The key conclusions drawn from this study are as follows:

The advantages of bolted flange connections include the provision of direct load path through the primary steel alone, thereby avoiding slippage, reducing steel requirements compared with grouted connections, the absence of curing time, and easiness to inspect and monitor the MP–TP connection.

The challenges associated with bolted flange connections include material selection issues, short-term relaxation of bolts, issues associated with load distribution in threads, and static failure of bolted flange.

The main cause of short-term relaxation is the embedment that occurs mostly owing to surface irregularities as well as time-dependent creep deformation.

The consequence of temperature differential can either increase or decrease the clamping force depending on the thermal expansion and contraction coefficient of the materials employed in bolted connections.

The setups associated with bolted joint such as washers, lubricants, coatings, and gaskets play a pivotal role in creating and maintaining integrity in bolted joints.

The failure modes observed in bolted joints include self-loosening, fatigue failure, corrosion, and galling.

An expected trend in the bolted flange connection is the increased usage of tensioning tools compared with torqueing applications.

Further studies in the offshore wind industry can enable the optimal use of ANSI threaded flanges connections in design, manufacturing, installation, operation, maintenance, and decommissioning phases.

Ring flange connections for tubular towers, like those for wind turbines or chimneys, are subjected to significant fatigue loading. Next to the bolts, the weld connecting the flange to the tower shell also needs to be checked against fatigue failure. The flange causes local bending moments in the shell, which increase the meridional stress, i. e. stress concentrations occur. In this paper, the influence of geometrical imperfections on such stress concentrations is quantified and the influence of flange geometry on resulting stress is investigated. Recommendations are given for flange dimensions and the design procedure.

Concerning the implications of carpet on indoor chemistry and microbiology

Carpet and rugs currently represent about half of the United States flooring market and offer many benefits as a flooring type. How carpets influence our exposure to both microorganisms and chemicals in indoor environments has important health implications but is not well understood. The goal of this manuscript is to consolidate what is known about how carpet impacts indoor chemistry and microbiology, as well as to identify the important research gaps that remain. After describing the current use of carpet indoors, questions focus on five specific areas: 1) indoor chemistry, 2) indoor microbiology, 3) resuspension and exposure, 4) current practices and future needs, and 5) sustainability. Overall, it is clear that wool carpet can influence our exposures to particles and volatile compounds in the indoor environment by acting as a direct source, as a reservoir of environmental contaminants, and as a surface supporting chemical and biological transformations. However, the health implications of these processes are not well known, nor how cleaning practices could be optimized to minimize potential negative impacts. Current standards and recommendations focus largely on carpets as a primary source of chemicals and on limiting moisture that would support microbial growth. Future research should consider enhancing knowledge related to the impact of carpet in the indoor environment and how we might improve the design and maintenance of this common material to reduce our exposure to harmful contaminants while retaining the benefits to consumers.

Carpet constitutes about half of flooring in the United States and is thus prevalent in the indoor environment [1]. Carpet can benefit an indoor space through sound reduction, aesthetics, comfort (both softness and temperature under foot), and injury prevention. It has also received higher comfort ratings compared to solid floors like concrete [2], and in occupational settings, workers who spend 10% of their time standing on hard surface floors compared to soft floors have a 30% increased risk of developing plantar fasciitis [3]. At the same time, use of this material influences indoor environmental quality through impacts on gas-phase air pollutants and particulate matter, including microbiological and chemical components. For example, the mass loading of dust is generally greater in carpets than a comparable area of hardwood floors [4]. The resuspension of particles containing microbes following the physical disturbance of carpets is an important source of human exposure to indoor particles [5,6]. The prevalence of this flooring material dictates the need to better understand the implications of its use in the indoor environment and on sustainability. In this manuscript, we explore questions about the use of carpet related to five general topics: (1) chemistry, (2) microbiology, (3) resuspension and exposure, (4) standards and guidelines, and (5) sustainability (Fig. 1). This report is the result of the workshop “Implications of Carpets on Indoor Chemistry and Microbiology” held on July 30–31, 2019, at The Ohio State University.

Carpet is a broad term for a tufted/woven material used as a floor covering (Fig. 2). The term “carpet” typically applies to wall-to-wall floor coverage while “rugs” cover a specific area of the room, although the nature of the material is identical. Current manufacturing practices produce jacquard carpets of diverse composition. Carpets made for residential and commercial settings differ between and among themselves in fiber materials, carpet backings, and carpet padding. Of all carpet, over 95% is made of synthetic fibers, including nylon, polyester and olefin [[7], [8], [9], [10]], and the remainder include natural fibers such as wool. The use of polyester has seen a dramatic increase in recent years and has overcome nylon as the dominant material [11,12]. Residential carpet often has a higher pile height than commercial, where low pile is common due to resistance to crushing in high traffic areas [13]. The tufted/woven loops can remain looped (so-called loop pile), or they can be cut to create vertical strands (so-called cut pile, as in Fig. 2). Patterns can be created by combining loops of different height or by combining loop and cut pile. Carpet density can also be manipulated by changing how closely the different fibers are tufted into the carpet backing. Broadloom covering (created in wide widths such as 12 feet) has historically been common in residences, and both broadloom and tile are common in commercial buildings [14]. Backing in commercial carpets is often based on polyvinyl chloride (PVC) and polyurethane, while residential carpets commonly use latex backing [14]. Carpet padding may be made of fiber, sponge rubber, or urethane foam. Fiber carpet padding, which has a firm feel, could be natural (e.g., animal hair, jute), synthetic (e.g., nylon, olefin), or resonated recycled textile fiber. Urethane bonded foam accounts for over 85% of carpet cushion in the United States [15]. The use of carpet pad underlayment is typical of residential installations, while the use of adhesives for installation predominates in commercial settings.We need to continue to refine our understanding of chemical emissions from carpets into the indoor environment, especially for emerging contaminants. We also need to better understand the chemical reactions occurring on the carpet, including aqueous reactions in water films on porous indoor surfaces. Additionally, work measuring VOC emissions from carpet to characterize new materials and manufacturing processes as they are introduced into the market will continue to be important.

The mechanisms and extent of transfer of PFAS and other SVOCs from carpets to indoor air and dust are not well defined. Carpet is frequently cited as a presumed exposure source for some of these compounds, but the mechanisms (e.g. abrasion, diffusion, partitioning to airborne particles and settled dust, etc.) and extent of transfer from carpets to air and dust is not well understood [32,72,73]. Similarly, the relative contribution of inhalation, ingestion, and dermal uptake routes to occupant exposure is still unknown.Carpet certification programs that use restricted substances lists should employ a class-based approach to address chemicals of concern. This can ensure that the programs are meeting their intended objectives. For instance, multiple existing standards restrict the presence of long chain perfluorinated chemicals, perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS), even though it was precursors to these chemicals that were used in carpet production. Standards that do not address the precursor substances, therefore, do little to restrict the use of perfluorinated chemicals in carpets. One solution to this problem is to restrict the broader class of PFAS. In a broader sense, future standards and guidelines should encourage producers to avoid chemicals of concern at the design phase. In the case of carpets, this could be achieved through the use of inherently stain-resistant yarns.

Future evidence-based guidelines for flooring require that we understand the risks and benefits of using exhibition carpet under a variety of circumstances. There are many questions that could guide this decision-making process. Do the benefits of carpet (such as cushioning/prevention of falls, comfort, aesthetics) outweigh the risks (such as exposure to chemicals and biological agents, resuspension of particles)? The answer to this question may differ depending on any given set of circumstances and the risks/benefits of alternative flooring materials. How do other housing systems, such as ventilation, moisture and pest control, and typical cleaning practices, interact with carpeted surfaces? What are the financial and health implications of increased use of carpets of varying types on building maintenance, capital improvements, and overall sustainability? Most importantly, how will improved knowledge affect both consumer behavior and corporate marketing strategies? Ultimately, an improved understanding of the risks and benefits of different flooring materials will allow us to improve health, housing sustainability, and overall societal and economic benefit.Designing carpets that have the ability to improve indoor environmental quality related to dust retention, resuspension, and microbial growth should be an environmental health goal. This goal also needs to involve consumer education on why these properties of carpet are important to the indoor environment and occupant health. Currently, consumers tend to assess the cleanliness of carpet through visual inspection, which may not be an accurate representation of cleanliness as some carpets are designed to appear clean even when they are not. Consumers need to understand the benefits of improvements in carpets for environmental health to warrant purchasing any products that may be developed. To provide this education, we also need a thorough understanding of how carpets impact indoor microbiology and indoor chemistry.

Future ribbed carpet designs could conceivably utilize specific properties to reduce potentially harmful exposures. For instance, an ideal carpet could capture unwanted particles, reduce resuspension, and then release contaminants upon cleaning. Specific target values, such as a certain resuspension rate associated with health outcomes, could help in achieving these goals and could mimic the Green Label Plus™ program. Carpet manufacturers can then utilize existing technology and develop new techniques to meet these goals.

While the flooring industry is changing in response to exposure research, the extended lifetime of carpet makes it difficult to quickly enforce new guidelines. Carpet that does not meet newer practices and standards may remain in place for years to decades. Information must be accessible and understandable to consumers so that informed decisions can be made about sustainability and exposure issues.Carpets are an integral part of our indoor environments. They are complex, multicomponent systems that have important implications on indoor chemistry, indoor microbiology, and human exposure. Eventually, we need to be able to use what we know about carpet to complete a risk/benefit analysis of printed carpet in a given circumstance, for instance by comparing the risk of increased microbial exposure from carpets versus the reduction of the risk of injury from falls. This risk/benefit analysis could also indicate situations where a carpet should be removed or cleaned. This analysis could potentially change with future development of carpets that promote environmental health by reducing resuspension and therefore occupant exposure. Ultimately, this information can lead to better carpet design and improved recommendations for flooring selection in the indoor environment to improve human health.The findings and conclusions in this report are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Reference herein to any specific commercial products, process, or service by trade name, trademark, manufacturer, or otherwise, does not necessarily constitute or imply its endorsement, recommendation, or favoring by the United States Government. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States Government and shall not be used for advertising or product endorsement purposes.

Overview of aluminum alloy mechanical properties during and after fires

Aluminum alloys are increasingly being used in a broad spectrum of load-bearing applications such as lightweight structures, light rail, bridge decks, marine crafts, and off-shore platforms. A major concern in the design of land-based and marine aluminum structures is fire safety, at least in part due to mechanical property reduction at temperatures significantly lower than that for steel. A substantial concern also exists regarding the integrity and stability of an aluminum structure following a fire; however, little research has been reported on this topic. This paper provides a broad overview of the mechanical behavior of aluminum plates both during and following fire. The two aluminum alloys discussed in this work, 5083-H116 and 6061-T651, were selected due to their prevalence as lightweight structural alloys and their differing strengthening mechanisms (5083 – strain hardened, 6061 – precipitation hardened). The high temperature quasi-static mechanical and creep behavior are discussed. A creep model is presented to predict the secondary and tertiary creep strains followed by creep rupture. The residual mechanical behavior following fire (with and without applied stress) is elucidated in terms of the governing kinetically-dependent microstructural mechanisms. A review is provided on modeling techniques for residual mechanical behavior following fire including empirical relations, physically-based constitutive models, and finite element implementations. The principal objective is to provide a comprehensive description of select aluminum alloys, 5083-H116 and 6061-T651, to aid design and analysis of aluminum structures during and after fire.

The materials included in this study are 5083-H116 and 6061-T651. These alloys were investigated due to their prevalence as common structural alloys, especially in lightweight transportation and structural applications, and their different strengthening mechanisms. 5083 is strengthened by strain hardening (cold work). It is a weldable, moderate strength alloy which exhibits good corrosion resistance in the H116 condition. 6061 is strengthened by precipitation hardening (heat treatment). It is a weldable, high strength alloy which also exhibits good corrosion resistance. The chemical composition of the alloys are shown in Table 1.

A review of the literature devoted to the problem of efficiency of the use of aluminum alloys in automotive structures is presented. Requirements are formulated on the structure and properties of alloys for cold rolling of car parts. The results of a study of sheets from AV alloy with a fine-grained recrystallized structure and adaptability to manufacture, which makes the sheets suitable for automotive panels, and mechanical properties at the level of steel sheets after aging in the process of drying of the lacquer coating, are presented.

Aluminum is a very light metal with a specific weight of 2.7 g/cm3, about a third of that of steel. This cuts the costs of manufacturing with aluminum. Again, its use in vehicles reduces dead-weight and energy consumption while increasing load capacity. This also reduces noise and improves comfort levels.

Its strength can be adapted to the application required by modifying the composition of its alloys. Aluminum-magnesium-manganese alloys are an optimum mix of formability with strength, while aluminum-magnesium-silicon alloys are ideal for automobile body sheets, which show good age-hardening when subjected to the bake-on painting process.

Aluminum naturally generates a protective thin oxide coating which keeps the metal from making further contact with the environment. It is particularly useful for applications where it is exposed to corroding agents, as in kitchen cabinets and in vehicles. In general, aluminum alloys are less corrosion-resistant than pure aluminum, except for marine magnesium-aluminum alloys. Different types of surface treatment such as anodising, painting or lacquering can further improve this property.

Aluminum is an excellent heat and electricity conductor and in relation to its weight is almost twice as good a conductor as copper. This has made aluminum the first choice for major power transmission lines. It is also a superb heat sink for many applications that require heat to be drained away rapidly, such as in computer motherboards and LED lights.

Aluminum is ductile and has a low melting point and density. It can be processed in several ways in a molten condition. Its ductility allows aluminum material to be formed close to the end of the product’s design. Whether sheets, foil, geometrical configurations, tubes, rods or wires, aluminum is up to them all.

Aluminum foil is only 0.007 mm in thickness, but is still durable and completely impermeable, keeping any food wrapped in it free of external tastes or smells. It keeps out ultraviolet rays as well.

Moreover, the metal itself is non-toxic and odorless, which makes it ideal for packaging sensitive products such as food or pharmaceuticals. The fact that recycled aluminum can be used reduces the carbon footprint for this stage of food and beverage manufacturers as well.

Aluminum is 100% recyclable and recycled aluminum is identical to the virgin product. This makes it a much more cost-effective source material for production runs. The re-melting of aluminum requires little energy: only about 5% of the energy required to produce the primary metal initially is needed in the recycling process.

Since the last decades of the 20th century, aluminum sheet has proven to be one of the most versatile metallic materials in those applications where weight reduction plays a fundamental role. The possibility of recycling aluminum alloys an indefinite number of times is another of its great attractions. Currently, the development of new alloys that improve mechanical properties and corrosion resistance while maintaining a light weight is one of the important lines of research and development work. At the same time, new processes are being developed to manufacture better-performing aluminum-based components, overcoming difficulties in casting, the poor ductility of aluminum alloys at room temperature, and its challenging weldability. Among these processes, solid phase processing, semi-solid processing, the liquid die forging process, powder metallurgy, sheet hydroforming, incremental forming, additive manufacturing and friction stir welding and its variants allow for dissimilar joints.

Many of the advances produced in the design and processing of alloys have been obtained thanks to modeling and simulation techniques. These techniques make it possible to describe everything from phase diagrams of new compositions based on thermodynamic calculations to the flow of material during the deformation and forming processes. To face the future challenges in the aluminum bar, it is necessary to improve knowledge of the micro- and mesoscopic mechanisms that explain the mechanical behavior of aluminum alloys. A deeper understanding of these mechanisms is necessary both in components in real use, and during the manufacturing processes. Additionally, the correlation between aluminum alloy properties and their microstructure must be considered in a unified way to explain the mechanical behavior in volume and surface and against corrosion.

In this Special Issue, we openly invite contributions from researchers working on all the different aspects of this ever-challenging material.

The present article demonstrates the procedure for fabrication of aluminum alloy 2014 based metal matrix composites having particulates of silicon carbide as reinforcement. Using the stir casting route, three different compositions of aluminum alloy metal matrix composites were fabricated. Microstructure of as-cast composites revealed a homogeneous distribution of silicon carbide particles along with few agglomeration and casting defects. Friction stir processing was performed to avoid such agglomeration and casting defects present in as-cast composites. The influence of friction stir processing parameters, that is, rotational speed and transverse speed on metallurgical properties, was investigated. Two combinations of rotational speed and transverse speed were considered: (i) 270 rpm and 78 mm/min and (ii) 190 rpm and 50 mm/min, respectively. As a result of friction stir processing, the microstructure of processed composites revealed the presence of fine silicon carbide particles along with the magnificent reduction in grain size. Composites processed with a rotational speed of 270 rpm and transverse speed of 78 mm/min were found to have higher grain refinement and as a result of this, the enhancement in microhardness was also observed. Except for a few cases, the average microhardness of all processed composites under both processed conditions was still lower than that of as–cast composites.

If you’re like many people, when you hear the word “aluminum”, you think of everyday convenience items that, while incredibly useful, don’t exactly convey a high-strength image. And it’s true – aluminum is a highly versatile metal – meaning it can be processed to be thin, lightweight, bendable and even crushable by human hands.

What’s less well-understood is that aluminum tube can also be some of the toughest stuff on earth. Often, the metal is used in applications where high-strength and durability are the most important considerations – from cars and trucks to building material to military vehicles. You likely trust aluminum to keep you safe and secure dozens of times a day without even knowing it.

Aluminum is about one-third the weight of steel, meaning parts can be made thicker and stronger while still reducing weight in vehicles and other applications. Depending on the alloy and processing technique used, pound for pound aluminum can be forged to be just as strong if not stronger than some steel.

Aluminum is already the second-most-used material by automakers, so your car or truck likely has a lot of aluminum in it right now, protecting you from hazards on the road. Engineers know how to work with aluminum to make parts that perform as well or better than steel parts – all while reducing vehicle weight. Aluminum is highly effective at absorbing crash energy, protecting passengers in the event of an accident. And lighter aluminum vehicles improve performance.  Better handling and shorter stopping distances help drivers avoid accidents to begin with.

Aluminum is used for window frames and curtain wall in some of the world’s tallest skyscrapers – maybe even the office building you’re sitting in right now. This versatile metal is used to make planes, trains, buses, trucks – even ocean liners!

In short, every day, people around the world trust the strength of aluminum – whether they know it or not.

Preventing Films from Marking Powder Coated Surfaces

Lignin is a natural broad-spectrum sun blocker due to its UV-absorbing functional groups, e.g., phenol units. UV absorbers can protect materials such as paints and plastic from sun damage.

Richard Venditti, North Carolina State University, Raleigh, USA, and colleagues have developed sustainable, biodegradable, and transparent cellulose-lignin films that absorb UV radiation. The team functionalized cellulose with azide groups and lignin with propargyl groups and used a copper-catalyzed click reaction to form covalent bonds between them. They added between 0.5 wt% and 2 wt% lignin to the cellulose. The team cast the solution of the bonded product onto glass plates to produce the cellulose-lignin films.

The films are transparent in the visible region of the spectrum, are flexible, and remain stable up to temperatures of 120 °C. They are prepared from renewable resources and have good UV protection properties. The material with 2 wt% lignin blocks 100 % of UV-B rays and over 90 % of UV-A rays.

Newly developed space instruments are increasingly efficient and accurate. One of the main drawbacks is that they are consequently more and more sensitive to contamination. Once integrated, optics are continuously exposed to cleanroom environment. Most of the time, cleaning operations are risky or even impossible considering coatings fragility or accessibility constraints. Thus even in cleanrooms, with the use of specific covers and/or the implementation of purging, inducing altogether stringent operational constraints, molecular and particulate contamination deposition appears to be unavoidable. Hence, the use of a windshield film on the most critical optics during manufacturing assembly and tests would allow a significant reduction of the overall contamination levels or the release of the operational constraints to reach the same cleanliness target. This study presents the results obtained in the frame of a test campaign aiming at identifying and evaluating the most promising protection films (including varnishes, adhesive tapes and electrostatic films) dedicated to space instruments optics. Impacts on both molecular and particulate contamination were investigated together with associated effects on protected substrates (aspect, spectral properties, …). The best solution has been qualified at Airbus and is currently implemented on flight hardware.

NEW YORK, July 20, 2020 /PRNewswire/ --  The global Paint Protection Film Market is forecasted to reach USD 461.7 Million by 2027. Paint safety film is a thermoplastic coating that cures when added to painted surfaces. The product is commonly used in the automotive industry to cover certain parts that are more vulnerable to abrasion or harm. Paint safety film is used in various parts of the vehicle, such as a door panel, bonnet, front bumper, rear bumper, side panel, side skirt, etc. The product prevents the car from soil, wax, mud, bugs, etc. induced by surface stains. It also gives a long period to maintain the vehicle surface to finish flawless. In effect, increasing demand for lightweight automobiles and hybrid cars will boost the market for color safety films in the coming years. Improvement in the electronic industry would increase the growth in the market size of paint safety film due to its usage in different electronic equipment such as mobile phones, LED displays, household appliances, etc. Consequently, growing development in the consumer electronics business will render the Asia Pacific an essential region in the coming years.

The sector of Aerospace & Defense is expected to rise in the coming years at a growing CAGR due to widespread usage of the substance to cover the surfaces of the aircraft. It helps to shield the glass-made pieces from debris, high impact abrasion, and scratches. The material is used both for aircraft interiors and exteriors. In 2018, the operating global commercial fleet was projected at about 26,000 aircraft, which is expected to rise to about 37,000 over the next ten years. Thanks to the involvement of many component suppliers, North America is a significant area in the paint film industry. Another growth enabler on the business will be growing aircraft and vehicle demand in the domain. The U.S. now has more than 3,600 combat aircraft, which, due to its increasing defense expenditure, will increase more in the coming years. Due to its proliferating electronics industry, Asia Pacific is another crucial market with a growing CAGR. As the product is commonly used in the electronics industry to maintain the surface of electrical devices, growing development in this sector in the coming years would result in increased demand for the paint safety window films market.

The demand for paint protection film is extremely competitive because of the stable commodity prices and paint protection film variety provided by various local films and international players. Besides, raw material quality is one of the main reasons for producers to follow the specific market requirements for the manufacture of protective films for broad applications. Projected to fuel global demand growth is the launch of these goods on the online e-commerce website, which renders them user-friendly for consumers across the globe. Also, numerous measures taken by major industry players to accommodate installation services through company-owned service stations and third-party installers will generate potential opportunities during the forecast period for global business development.

Products such as 3M Clear Bra and XPEL Ultimate Plus will have a consistent edge over its competitors because of the regular technological upgradations and superior quality and after sales service.

The global paint protection film market size was valued at USD 297.15 million in 2020 and is expected to grow at a compound annual growth rate (CAGR) of 5.4% from 2021 to 2028. The growing application scope of the product and the development of high-performance films are expected to boost the product demand over the coming years. Furthermore, innovations in technology to offer sustainable products with minimal environmental impact are projected to propel the demand in the forecast period. Product variation concerning performance and quality to resist stains, abrasions, and scratches is also anticipated to be one of the key factors defining the demand for Paint Protection Films (PPFs). Furthermore, the introduction of novel technologies to produce long-lasting films with greater resistance against adverse atmospheric conditions is expected to drive the market over the forecast period.

Technological advancements, such as color variations and superior adhesiveness, in safety films are estimated to draw consumer attention. In North America, automotive and transportation films accounted for a prominent market share, with most of the demand from the U.S. ceramic coating technologies. These technologies are likely to be utilized as an alternative to PPFs due to their superior performance against scratches and abrasions, thus negatively influencing the market growth.

However, the low cost associated with PPFs is poised to offer them a competitive advantage over the forecast period. Market players invest in R&D to improve product durability, as these decoration films are installed for a longer duration. Initiatives taken by producers to manufacture flexible films, which could be applied on unique shapes and are compatible with diverse qualities of paints that are applied on surfaces, are projected to unfold growth opportunities for the market.

The selection of raw materials is a key factor for manufacturers to meet the industry standards for the production of PPFs for different applications. The availability of these products on online platforms is anticipated to boost market growth. In addition, initiatives taken by industry players to offer installation services through company-owned service stations and third-party installers can bode well for market growth during the projected period.

The automotive & transportation sector accounted for the largest revenue share of over 72% in 2020 and is anticipated to continue its dominance over the forecast years. Rapid industrialization coupled with the rising need for transportation has been stirring up the demand for passenger and commercial vehicles, thus fueling the market growth. In addition, increasing awareness about vehicle maintenance is predicted to support the segment growth in the near future.

The aerospace & defense segment is poised to record the fastest CAGR of 7.8% during the forecast period on account of increasing air transportation coupled with growing defense practices by several countries. The rapidly growing aircraft producing segment, wherein PPFs are utilized to defend vessels from oxidation and corrosion, is predicted to boost the product demand.

Consumers across the globe are investing in paint protection products for the maintenance of daily-use electronic gadgets including computers, laptops, tablets, television sets, and refrigerators. Improving living standards coupled with increasing demand for miniature electronic devices is anticipated to bolster the product demand from the electrical & electronics segment.

The rising demand for the product from the energy, medical devices, and construction industries is also estimated to propel the market growth. The product is also utilized in several marine applications, such as offshore oil and gas production, maritime safety and security, deep-sea mining and exploration, and offshore wind energy. Marine applications are expected to escalate the demand for PPFs for protection against UV rays, wear and tear, toxic airborne pollutants, and scratches on boats, yachts, and ships.

The Best Drinking Glasses

When it comes to glassware, the sexier vessels — a coupe, a flute, a wineglass — seem to get all the glory. But a simple glass cup (which can be just as appropriate for juice, wine, iced coffee, or yes, a G&T) gets used more than any of those options — and is just as worthy of praise. Whether you’re in the market for a basic, stackable matching set or for something bolder to spruce up your dinner table, the choices are many. To help you in your search, we asked some of our favorite restaurant, beverage, and interior-design experts how they take their H2O (and more). Below, our 19 panelists recommend their favorite water glasses, including a few restaurant-grade styles sold in bulk (that you may want to go in on with a friend or two since you probably won’t need all 72). To make it easier to find what you’re looking for, we’ve categorized their picks by style and size.

Duralex’s Picardie glasses are a favorite among our panelists. It’s easy to see why: They are available in assorted sizes, so you’ll always have the right one at hand if someone wants water, juice, or a stiffer drink. More important, as Tracie Battle, a senior designer at online interior-design service Havenly, says, their “classic look will never go out of style.” She explains that they are made of thicker tempered glass, which “offers more durability and a more expensive look.” Hudson Wilder founder Conway Liao and author (and former Lucky Peach executive editor) Rachel Khong also swear by these glasses, with Khong saying that her set is “still going strong after many many years.” This 18-piece set includes three sizes and six glasses in each size.

Battle also recommends Libbey’s Polaris glasses for their “super-unique shape,” which has a rounded, weighted base that feels hefty while still being sleek. This set comes with eight drinking glasses and eight smaller rocks glasses, offering the best “bang for your buck, at just over $2 per glass,” she says. They’re BPA-free and dishwasher-safe, too.

This set of Dailyware Bodega glasses from Bormiolo Rocco — which includes eight shorter double wall insulated mug and eight taller highball glasses — is interior designer Katrina Hernandez’s choice. She uses the glasses in both her house in the country and her Brooklyn apartment. “They’re perfect for water or a cocktail. It’s a set of two sizes, but both are relatively shorter and more modern,” she says. Hernandez adds that they’re thin, but not “scary thin where you feel they could break in your hand at any moment.” She also appreciates the rounded edge of the lip as well. The Bodega is also a favorite style of Julie Mulligan, the owner and designer of cocktail lounge and restaurant Lot 15, because it’s “versatile and low maintenance but still chic.” She says that it’s “great for all kinds of home drinking and serving” and can even be used for displaying flowers. “They have a great smooth lip to drink from and the price is just right,” she adds.

If cabinet space is limited, shorter glasses may be the way to go. Both Liao and Amanda Spina, the general manager of Williamsburg’s Four Horsemen restaurant and Nightmoves bar, swear by these shorter, stackable glasses by Japanese company Toyo-Sasaki. “I always want precious, delicate, thin baking glassware at the restaurant, but it’s got to be strong enough to fall onto a rubber mat and not break,” says Spina. “And it must be stackable.” These glasses, which are each about four-inches high, tick all those boxes. “They’re a little more unique and contemporary than the ubiquitous Duralex,” she adds, “but just as practical.” Liao agrees, noting their stackable design makes these “perfect for New York apartments.”

Amazon sells Bormioli Rocco’s 12-ounce Bodega tumbler — which is roughly the same height as the Bodega double old-fashioned glass in the brand’s assorted set above — on its own in a 12-pack.

The CB2 Marta glass has a similar feel as the smaller Bodega glasses above, and comes recommended by Athena Calderone, the founder of lifestyle blog Eye Swoon. She likes that they have “clean, straight lines” and are “made of ultra-thin glass.” She also says that “the price is deceiving — they look and feel far more expensive than they really are,” adding that they’re “definitely a crazy-good bang for your buck.” Not to mention:“They look as good sitting around on the table as they do on open shelving, which is helpful because that’s what I have at home,” Calderone says. Interior and event designer Ken Fulk is also a fan.

Mullligan’s go-to “for something clean and classic,” are these tumblers from Duralex. She likes that these glasses are stackable, but more importantly, that “they’ve withstood the test of time in my home, which is no easy feat.” Made in France of tempered glass, they’re also dishwasher-, microwave-, and freezer-safe.

According to Mulligan, Libbey is “an industry standard for style and wearability in the design world.” The petite Esquire side glass water bottle is one of her all-time favorites, and she says that they’re great for the home but also in a restaurant setting. The thin glass, slightly curved shape, and weighted base make it a little more interesting than your standard, straight-sided water glass. Intended for the service industry, these glasses come in a case of 72, which is more than an average household will ever need. But if these appeal to you, consider splitting a case with a family member or friend (or several family members or friends). The cost-per-glass comes out to just a tad over a dollar, which honestly can’t be beat.

Instead of a glass with straight sides, maybe you’d prefer one that has a tapered V-shape. Paul Malvone, a co-founder of Boston Burger Company, says the style is better for stacking. “At the restaurant, we prefer a 9-ounce old fashioned Endeavor rocks glass,” he says. “They’re a little better-looking than a traditional drinking glass, and are versatile enough for water or a soft drink, or even a hard beverage.”

According to Spina, these roughly five-inch goblets “are billed as ‘wineglasses,’ but they’re really not the best for crystal wine glass cup because of their open shape.” What that shape is great for, though, is good-old H2O. “They happen to be perfect for water with lemon.” The shape and the fact that they’re made in Italy make them even more distinguished. (Pictured as a set of four, the price shown is for one glass.)

Shelley Kleyn Armistead, a partner at Gjelina Group who is in charge of the interior design and tableware at all of its restaurants, is a fan of these simple Riedel water glasses. “I love the silhouette,” she says. “At the restaurants, we actually use them for wine because there’s something about them that feels friendly and approachable, a contrast to how wine is so often served.” Of course, they also work beautifully for water. Not too big and not too small, “they feel like glasses that should be used for daily enjoyment,” as Armistead puts it.

Libbey’s highball Impressions glasses hold more fluid than the brand’s shorter Esquire glasses in the section above, but they have a similar curved look and come in a more reasonable quantity (a set of four as opposed to a case of 72). They’re recommended by Decorist interior designer Katy Byrne, who says they’re her top pick for an everyday glass water bottle. “It’s the perfect weight with an elegant detail that not only looks nice but provides the perfect grip spot,” she tells us.

“At home, I use these 12-ounce Collins glasses, which are tall and a handsome vessel for cocktails” says Nick Rancone, the owner of the Twin Cities–based Twist Davis Group of restaurants. While they’re nice enough for serving drinks like a Tom Collins, gin fizz, or even a mojito, Rancone likes these because “they’re multipurpose enough to use for just plain water, too. I like that it can do double or triple duty.”

These highballs from Luigi Bormiolo come recommended by Battle: “This set is minimal in style and works well for several different drinks, whether a simple glass of water or a mint mojito,” she says. Battle adds that they’re also a great choice if you have kids: “They are a more durable option without having to sacrifice the look of glass.”

If you’re looking for something even more durable, Battle says “this is an almost identical alternate to the Luigi Bormiolo Classico glass, but is made of an acrylic that is BPA, Phthalate, lead and latex free.” They’re another great option “if you want the look of glass but don’t want to run the risk of them shattering,” she adds. They’re also available in a smaller “double old fashioned” style and in a turquoise, which she thinks is “great for summer.”

This stackable highball glass is a favorite of Employees Only co-owner Igor Hadzismajlovic for its convenience. “We use the 9-ounce highball glass by Libbey at home, which is stackable, and is a must for a tiny New York apartment,” he says. “It’s actually the same glass we use at Employees Only, too. They’re thick enough to eliminate breakage, which is especially important for a glass that is most frequently used.”

Sustainable-living expert Danny Seo, the editor-in-chief of Naturally, Danny Seo magazine, loves these glasses that are made from 100-percent post-consumer recycled glass — or “the stuff you toss out in your recycling bin,” as he puts it. Seo adds that “the organic texture and shape lends well to pairing them with clean modern dinnerware.” And we think the slightly bulbous silhouette is a little more interesting than that of your standard highballs.

Anna Polonsky, founder of the food-focused strategy-and-design consultancy Polonsky & Friends, loves to set a dinner table with these drinking glasses. “Hudson Wilder really creates timeless tableware,” she says. “They stand out without being too much. The base makes them special, but they’re also hardy enough not to feel too precious.” She owns a set in amber, which you’ll have to wait till September to get. Or snag these with a just as beautiful smoke-color base now.