#ROCKSPACE WIFI extender
Text
Re.rockspace.local
The private web address re.rockspace.local is responsible to let you interact with your WiFi extender. If you have a Rockspace range extender, you can get access to it through this private web address. The URL can help you configure or manage your extender’s wifi network without any cables or wires.
All you have to do is, connect to the extender and go to the re.rockspace.local web page. The web-based interface does not even ask for an active internet connection in order to get inside your device. Want to learn how to login to the Rockspace range extender through this address, follow the steps below:
Firstly, ensure that your extender is plugged into the power outlet.
Go to a web browser on a device connected to the extender.
Type http://re.rockspace.local in the browser and hit Enter.
Put down the username and password upon reaching the re rockspace local login page.
Make sure you enter the login credentials carefully.
Click Login. You will log into the Rockspace wifi extender successfully.
That was all about the Rockspace WiFi extender and how to login to it using the private web address.
0 notes
Link
To connect Rock Space WiFi extender to new router, you need to reset your extender. Press and hold the reset button to restore the factory default settings.
Login to the extender using re.rockspace.local and start with the setup wizard. Connect the extender to a new router and finalize the settings to complete the setup process.
0 notes
Text
How To Connect Rockspace Wifi Extender Setup?
Rockspace wifi extenders are the most convenient and quick solution to increase the range of your existing Wifi.
To connect your rockspace wifi range exetnder to your phone or laptop, follow these steps:
Before connecting, switch off your mobile network.
Then, connect the WIFI extender to an electrical outlet.
Wait until the indication remains solid on.
Open WIFI on your Android, iPhone, or PC now.
To connect, select ROCKSPACE WIFI EXTENDER.
After a successful connection, open the web page and enter re.rockspace.local to configure the WIFI extender's password.
Locate the existing WIFI network that you want to expand, and then type on the existing WIFI network.
Finally, it has been linked.
You can now relocate it to a location where the networks are poor (dead zone area) or where you want to expand your network.
Default Login for Rockspace Wifi Range Extender
Before proceeding with the extender device configuration, you must have the login credentials for your ROCKSPACE booster device in order to conveniently access settings and control it swiftly. In addition, the default Login IP address, username, and password are printed on the ROCKSPACE Sticker, and a simple user manual is supplied with the box.
The default login URL is re.rockspace.local, and the IP address is 192.168.10.1**.**
Default username: NA
ROCKSPACE password- For the first time you log in, you must create a new password.
When you have everything ready to set up a range extender device, it is time to move on to the next stages.
Open your WEB BROWSER and navigate to re.rockspace.local or 192.16810.1, then wait for the login screen to load. During the initial configuration of the range extender, you must now generate a new login password. So enter a strong login password and then click the next button.
Final Words
These were the steps to assist you set up and log in to the Rockspace wifi Extender dashboard. If you are having trouble logging in, you may contact our customer service, we will assist you with your problem.
Visit: https://re-rockpacelocal.com/rock-space-wifi-extender-setup/
#rock space wifi extender#rockspace wifi extender setup#rock space wifi extender setup#re.rockspace.local#re rockspace.local#rockspace login#http://re.rockspace.local#rockspace wifi extender#http //re.rockspace.local
1 note
·
View note
Text
0 notes
Text
Connect Rock Space WiFi Extender to New Router
0 notes
Text
Rockspace WiFi Extender Setup
A Rockspace WiFi extender Setup can significantly enhance your wireless network coverage, ensuring a strong and stable connection throughout your home or office. Setting up your Rockspace WiFi extender is a straightforward process. Step by step guide on how to set up a Rockspace WiFi extender:
Setting up Rockspace WiFi Extender:Manual Method
Step-by-step guide Rockspace WiFi extender setup manually. This guide assumes a generic setup process; the specific steps might vary slightly based on the model you have. Follow these steps to manually set up your Rockspace WiFi extender:
Plug in the extender near your router and wait for the power LED to become solid.
Connect your device (computer or smartphone) to the WiFi network named "Rockspace-XXXX" (where XXXX represents the last 4 digits of your extender's MAC address).
Open a web browser and enter "ap.setup" or “192.168.10.1" in the address bar.
To finish the setup, follow the on-screen steps, which include selecting your existing WiFi network and entering its password.
Once the extender connects to your router's network, you can relocate it to an optimal location.
Following these steps should help you manually set up your Rockspace WiFi extender. Remember, it's important to consult your extender's specific user manual for accurate and detailed instructions to your model.
Rockspace Extender Setup using WPS method
Rockspace WiFi extender Setup using the WPS (Wi-Fi Protected Setup) method can be a quick and convenient way to extend your WiFi coverage:
Plug in the extender and wait for the power LED to become solid.
Press the WPS button on the extender.
Within 2 minutes, press the WPS button on your router.
Once the extender's WiFi LED becomes solid, the setup is complete.
Note: The WPS setup process might vary slightly depending on the model of your Rockspace extender. Please refer to the user manual that came with your extender for precise instructions.
How do I perform a factory reset on a Rockspace WiFi extender?
To perform a factory reset on a Rockspace WiFi extender, follow these steps:
Locate the reset button on the extender (usually on the side or back).
Use a paperclip or pin to press and hold the reset button for about 10 seconds.
When the LEDs begin to flash, release the button.
The extender will reset to its default settings.
By performing a factory reset, you'll essentially start over with a clean slate, allowing you to set up the extender as if it were brand new. Always refer to your specific extender's manual for the most accurate and detailed instructions on performing a factory reset.
Update Rockspace WiFi Extender Firmware
Updating the firmware of your Rockspace WiFi extender is important to ensure that it's running the latest software version, which can improve performance, security, and functionality. Step by step general guide on how to update the firmware:
Visit the Rockspace official website and navigate to the support section.
Enter your extender's model number to find the latest firmware version.
Save the firmware file to your computer after downloading it.
Log in to the extender's web interface (using the IP address from the manual setup step).
Look for the "Firmware Update" section and upload the downloaded file.
Wait for the update to complete and do not interrupt the process.
Note:That the exact steps may vary depending on the specific model of your Rockspace WiFi extender. Always refer to the user manual or documentation provided by Rockspace for accurate and model-specific instructions.
Troubleshooting Steps:
If you're experiencing issues with your Rockspace WiFi extender Setup, there are several troubleshooting steps you can take to identify and resolve the problems.Here is a list of basic troubleshooting steps.
Ensure the extender is within a reasonable distance from the router.
Check that the extender's power LED is solid and not blinking.
Verify that you are connecting to the correct extended WiFi network.
Restart both the extender and your router.
Make sure the WiFi password is correctly entered during setup.
Update the firmware on the extender to the most recent version.
Perform a factory reset and set up the extender again from scratch.
By following these setup and troubleshooting guidelines, you can maximize the performance of your Rockspace WiFi extender and enjoy seamless connectivity across your space. If persistent issues occur, referring to the product's user manual or contacting Rockspace's customer support can provide further assistance.
0 notes
Link
Get your Rockspace wifi range extender up and running in no time. Follow our easy step-by-step guide for setting up your extender and expanding your wireless network range. Enjoy the improved coverage and faster internet speeds today!
1 note
·
View note
Video
youtube
Rock Space AC750 and Ac1200 Range Extender Setup
0 notes
Text
How to Configure a Rockspace WiFi Extender?
The Rockspace WiFi extender setup is a straightforward process. Begin by plugging the extender into a power outlet within the range of your existing WiFi network. Once powered on, connect your computer or mobile device to the Rockspace_ext network using the default password provided in the user manual. Follow the on-screen instructions to log in (use the default username and password from the manual), select your existing WiFi network, and enter its password. Complete the setup process by following any additional prompts. Once configured, the Rockspace extender will amplify your WiFi signal, providing extended coverage for a more robust wireless connection.
Read More:-
1 note
·
View note
Link
Rockspace AC1200 WiFi Range Extender, 1200Mbps Dual Band WiFi booster, 2.4 GHz and 5GHz Wifi Repeater, WiFi Extender Booster Wireless with 1 Ethernet Port,Work with Any Routers,WPS Easy Setup, UK Plug We have a great collection of WFH products in our online shop. Our shop includes other essential remote home working devices like Webcams, Chairs, Tables and much more. Lets improve your WFH enrolment today with the Rockspace AC1200 WiFi Range Extender, 1200Mbps Dual Band WiFi booster, 2.4 GHz and 5GHz Wifi Repeater, WiFi Extender Booster Wireless with 1 Ethernet Port,Work with Any Routers,WPS Easy Setup, UK Plug. https://www.remoteworkingoffice.com/product/wifi-extender-1200mbps-wifi-booster-range-extender-wifi-repeater-ac1200-wireless-signal-booster-5g2-4g-dual-band-wifi-amplifier-with-ethernet-port-access-point-and-wps-coverage-120-%e3%8e%a1-u/?feed_id=1682&_unique_id=64fc882d6da6a #homeoffice #remoteworking #ratemyoffice #homeworking #rwo #remoteworkingoffice
0 notes
Text
The login password of a router keeps unauthorized users from accessing the router and the Wifi password keeps unwanted users from accessing the re.rockpsace.local network. If a user has forgotten the Wifi password of the router’s network he can fetch it through the web management window of the router.
1 note
·
View note
Text
Only a PC and a search engine are required. To the gateway, the laptop must join the packet group Re rockspace local login page. Using an Ethernet cable, fix your range extending in a straight line to the system. Visit here-
0 notes
Link
If you are looking for help with how to Reset Rock Space Wifi Extender, you can use the push button method as well as the app method to do so.
For details on how to proceed with the reset process, read through the setup guide on our website now or reach out to the team at our end now.
0 notes
Text
How to Reset Rockspace Wifi Extender
If you have come across one such reason and wondering How To Reset Rockspace Wifi Extender then this is your read. If you are facing issues with your Rockspace wifi extender that can not be solved by basic troubleshooting then resetting the device is your last resort.
https://re-rockpacelocal.com/reset-rockspace-wifi-extender/
0 notes
Text
Rockspace extender speed
Here you can resolve rockspace wifi extender speed drop issue with our help.
0 notes
Last Seen Blogs
